Mildly built NA B16A3 with P30 ECU

Calibrations for S-Manager - Use all calibrations at your own risk (dyno tuning recommended)
Post Reply
namato40
Posts: 4
Joined: Mon Mar 06, 2017 11:34 am

Mildly built NA B16A3 with P30 ECU

Post by namato40 » Fri Apr 21, 2017 5:40 am

Hi Forum,

I have a mildly built naturally-aspirated B16A3 from a Del Sol that I need a basemap for. I have checked the Hondata built-in logs and the only B16 built-in maps include forced induction via supercharging or turbocharging.

My build includes:

Stock Del Sol B16A3 OBD1 P30 ECU

Internals:
B16A3 bored .010 over
OEM CTR B16B pistons (.010 over) (higher compression than stock b16a3 ratio)
Stock bottom end beyond pistons.
New bottom end bearings
CTR single crank pulley

Valvetrain:
Supertech dual valve springs for all 16 valves
Supertech titanium retainers for all 16 valves
OEM ITR camshafts and cam gears

Intake:
OEM ITR intake manifold
OEM B16 throttle body
Aftermarket CAI
OEM O2 sensor

Exhaust:
PLM 4-2-1 Toda B-series rep header

Fueling:
OEM 240CC injectors
Walbro 255LPH fuel pump

Transmission:
Exedy replacement clutch
OEM flywheel
NO LSD

If there are any other parts that I did not include they're most likely OEM.

If someone could help me develop a basemap or even give me a basemap that would be much appreciated. I'm completely new to Hondata tuning and could use a guide even after reading the Hondata supplied information with the S300 Manager program and online research.

Please and thank you!

Jun43
Posts: 251
Joined: Mon Aug 01, 2016 2:59 pm

Re: Mildly built NA B16A3 with P30 ECU

Post by Jun43 » Fri Apr 21, 2017 12:02 pm

I would just run a ITR or CTR stock base map if you are just trying to start the car. You will need a wideband to tune or bring it to a tuner


edit:

https://www.hondata.com/forum/viewtopic ... 16b#p83542
run at your own risk

namato40
Posts: 4
Joined: Mon Mar 06, 2017 11:34 am

Re: Mildly built NA B16A3 with P30 ECU

Post by namato40 » Fri Apr 21, 2017 12:09 pm

Where can I find a CTR/ITR stock basemap?

Jun43
Posts: 251
Joined: Mon Aug 01, 2016 2:59 pm

Re: Mildly built NA B16A3 with P30 ECU

Post by Jun43 » Fri Apr 21, 2017 12:11 pm

namato40 wrote:
Fri Apr 21, 2017 12:09 pm
Where can I find a CTR/ITR stock basemap?
read the edit part

namato40
Posts: 4
Joined: Mon Mar 06, 2017 11:34 am

Re: Mildly built NA B16A3 with P30 ECU

Post by namato40 » Fri Apr 21, 2017 12:12 pm

Didn't see that until after. Thanks!

Zperformance
Posts: 100
Joined: Thu Jul 14, 2016 12:32 pm
Location: Fresno,Ca

Re: Mildly built NA B16A3 with P30 ECU

Post by Zperformance » Sat Apr 22, 2017 10:12 am

I wouldnt run the itr basemap. I noticed it runs higher timing, i would start off with a b16 and add fuel start from there.

namato40
Posts: 4
Joined: Mon Mar 06, 2017 11:34 am

Re: Mildly built NA B16A3 with P30 ECU

Post by namato40 » Sun Apr 23, 2017 3:27 pm

More fuel than the stock amount from B16a or B16B?

Post Reply