fault with flashpro firmware

FlashPro Manager software
Post Reply
schoeung
Posts: 4
Joined: Tue Apr 29, 2014 6:38 pm

fault with flashpro firmware

Post by schoeung » Wed Jun 18, 2014 7:05 pm

hi, im having a problem uploading a cal. Everytime i try it says;

"The last flashpro upload failed,failure information : code 0 step 0 adress 0x00000, explanation: there is a fault with the flashpro firmware"

as of yesturday, i have the flashpro manager 1.9 and when i plugged in my flashpro, it updated the firmware. Now i can't up load and cals. Any help or info please??

User avatar
Hondata
Site Admin
Posts: 8771
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: fault with flashpro firmware

Post by Hondata » Thu Jun 19, 2014 8:02 am

Please tell me what your serial number is, then use the 'send support information to hondata' menu item.
Hondata

schoeung
Posts: 4
Joined: Tue Apr 29, 2014 6:38 pm

Re: fault with flashpro firmware

Post by schoeung » Thu Jun 19, 2014 8:58 am

Thanks for the reply, but it works now. :)

R3KONT3K
Posts: 7
Joined: Mon May 08, 2017 8:58 pm

Re: fault with flashpro firmware

Post by R3KONT3K » Wed May 10, 2017 8:12 pm

I now have this problem also - Just after updating to 2.6.8 - Now can't Upload to it same error statement after trying

flashpro upload failed Code 0 Step 0 Address 0x000000
Last edited by R3KONT3K on Wed May 10, 2017 8:17 pm, edited 1 time in total.

R3KONT3K
Posts: 7
Joined: Mon May 08, 2017 8:58 pm

Re: fault with flashpro firmware

Post by R3KONT3K » Wed May 10, 2017 8:17 pm

schoeung wrote:
Wed Jun 18, 2014 7:05 pm
hi, im having a problem uploading a cal. Everytime i try it says;

"The last flashpro upload failed,failure information : code 0 step 0 adress 0x00000, explanation: there is a fault with the flashpro firmware"

as of yesturday, i have the flashpro manager 1.9 and when i plugged in my flashpro, it updated the firmware. Now i can't up load and cals. Any help or info please??
What did You do to Fix It??? I having Same Issue

User avatar
Hondata
Site Admin
Posts: 8771
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: fault with flashpro firmware

Post by Hondata » Thu May 11, 2017 8:17 am

Please tell me what your serial number is, then use the 'send support information to hondata' menu item.
Hondata

R3KONT3K
Posts: 7
Joined: Mon May 08, 2017 8:58 pm

Re: fault with flashpro firmware

Post by R3KONT3K » Sat May 13, 2017 11:49 pm

my Serial # is : FP-2012Si-113518
FlashPro Mngr: 2.6.8.0
2015 Civic Si Coupe

can't upload even when connected via laptop-flashpro-obdII- still gives error: flashpro upload failed Code 0 Step 0 Address 0x000000 Reason: There is a Fault with FlashPro Hardware


And Yes: - I have Used the "send support information to Hondata option" a couple of times - w/ no response

Emailing support now with all the issues I am noticing so far:

RPMS increased is intermittent: sometimes can go to 7600 from 2nd to 3rd gear sometimes it cuts fuel at 7k just like its stock - like every other run to redline:

Launch Control does not work at all - cancel button does not show me LC Limit - clutch depressed in first gear - ebrake - TC off - CC off - in every different combination does not work - flashed a couple times - does not work.

User avatar
Hondata
Site Admin
Posts: 8771
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: fault with flashpro firmware

Post by Hondata » Sun May 14, 2017 10:39 am

The 'send support information to Hondata' is only monitored when we request it. It says this when you send it.

There is a fault with your FlashPro hardware. Email support@hondata.com with you serial number, name, address and phone and we will issue a RMA.
Hondata

R3KONT3K
Posts: 7
Joined: Mon May 08, 2017 8:58 pm

Re: fault with flashpro firmware

Post by R3KONT3K » Sun May 14, 2017 9:23 pm

I e-mailed you guys this morning with all the info - thanks for all the help!

johnmc83
Posts: 3
Joined: Tue May 16, 2017 7:53 pm

Re: fault with flashpro firmware

Post by johnmc83 » Tue May 16, 2017 8:06 pm

As of today I am experiencing the exact same problem and error message when I updated FP manager software. I cannot load a cal to FP unit but it will datalog. Message is same...
The last Flashpro update failed.
Failure information : Code 0 Step 0 Address 0x000000
Explanation: There is a fault with the Flashpro hardware.

Serial number is FP-2012Si-113381

Please advise

9thGencivic
Posts: 1
Joined: Sat Sep 14, 2019 10:00 am

Re: fault with flashpro firmware

Post by 9thGencivic » Sat Sep 14, 2019 10:05 am

I am having this same issue. Just updated my flashpro for the September update now I can’t download my calibrations.

Post Reply