Stock TB is closing after 7000rpm

FlashPro questions & answers specific to the 2007-2008 US TSX
Post Reply
Malkolm666
Posts: 48
Joined: Thu Aug 09, 2007 6:06 am

Stock TB is closing after 7000rpm

Post by Malkolm666 »

Hi, I have a -04 CL9 with TSX 07 ecu, and flashpro. Have driven it with flashpro for over a year now. With the stock engine It never was never any problem(I attache a log from the dyno "rsp_231hk"). I have no CELs. Everything else works great.

Now I have built engine with higher comp and DC stage4 cams. And also you have updated the flashpro 2 times in september.

There is a problem with the DBW now, the ThrottleBody starts to close after 7000rpms, same stock TB, I used the same calibration, just changed fuel, ignition, VTC and vtec in it. Max power is at 7150rpm when TPlate is 89% and falling like a rock. This engine should get the peak at 7800-8300rpm. So I miss at least 1000rpm.

I have read all the posts on this forum about DBW problems, I know the different on the 2 different DBW-systems, I know all about that a larger TB can make alot of problems, I have read the flashpro help Content so many times now. Have tried to change so many things in the calibration. Have reset ecu. Have done idle learn procedur, I have also read the TSX CL9 WSM about Thottle body, the relay, the modul, the TB, the cruise modul etc etc..

The only electrical thing that Ive changed is that I updated the Flashpro software twice. nothing else.

Then I also have a question,"Target Throttle Plate" table, can you please add 7500rpm and 8000rpm into it? Please?
Attachments
galten_NYA_motorn_278hk_276nmLog2.fpdl
(29.87 KiB) Downloaded 198 times
GaltenV3mapp32_231hk_253nm.fpcal
(16.62 KiB) Downloaded 200 times
GaltenV3mapp86.fpcal
(18.07 KiB) Downloaded 205 times
galten_NYA_motorn_278hk_276nm.fpdl
(9.36 KiB) Downloaded 192 times
galten_rsp_grenror_231hk_253nm.fpdl
(8.62 KiB) Downloaded 191 times
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Stock TB is closing after 7000rpm

Post by Hondata »

You're going too fast - it is a speed limiter which starts at about 220 kph and closes the throttle to limit to 240 kph. We'll disable it for the next release.
Hondata
Malkolm666
Posts: 48
Joined: Thu Aug 09, 2007 6:06 am

Re: Stock TB is closing after 7000rpm

Post by Malkolm666 »

Okey, thanks. Im gonna dyno next time on a lower gear.

Do you have a time frame for next release? A couple of weeks? A month? More?
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Stock TB is closing after 7000rpm

Post by Hondata »

1-2 weeks
Hondata
Malkolm666
Posts: 48
Joined: Thu Aug 09, 2007 6:06 am

Re: Stock TB is closing after 7000rpm

Post by Malkolm666 »

I found the speed limiter, its under Speed Cut in "rev Limits". But that was set to 328kph, why is it slowing done the TB at 217-220kph? A bug?
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Stock TB is closing after 7000rpm

Post by Hondata »

No, there are two speed limiters. One rev limits, the other closed the throttle body.
Hondata
Post Reply