K20/k24 flash pro map help

Calibrations for FlashPro Manager - Use all calibrations at your own risk (dyno tuning recommended)

Post Reply
Mikeyaka23
Posts: 2
Joined: Sun Mar 03, 2024 3:59 pm

K20/k24 flash pro map help

Post by Mikeyaka23 »

I got a 2008 civic 8th gen k20/k24 build that I just started for the first time today with a 410cc file found on forums by EFICU. It started and idled nice but I turned off the car because I still need to install the rest of my exhaust.

Anyone can help with a map for my setup below?

My build list:

K20z3 head with k24a bottom end
Drag cartel 3.2 camshafts
K20z3 cam gears I believe they’re 50 vtc
95lb springs and retainers
72mm k tuned throttle body
3 inch short ram cold air intake
K tuned headers
3 inch rev9 exhaust
4 piston Rsx type s oil pump
410cc OEM rdx injextors
340lph fuel pump
User avatar
CalibratEd
Posts: 1481
Joined: Fri Feb 07, 2020 3:20 pm
Contact:

Re: K20/k24 flash pro map help

Post by CalibratEd »

Mikeyaka23 wrote: Sun Mar 03, 2024 4:20 pm I got a 2008 civic 8th gen k20/k24 build that I just started for the first time today with a 410cc file found on forums by EFICU. It started and idled nice but I turned off the car because I still need to install the rest of my exhaust.

Anyone can help with a map for my setup below?

My build list:

K20z3 head with k24a bottom end
Drag cartel 3.2 camshafts
K20z3 cam gears I believe they’re 50 vtc
95lb springs and retainers
72mm k tuned throttle body
3 inch short ram cold air intake
K tuned headers
3 inch rev9 exhaust
4 piston Rsx type s oil pump
410cc OEM rdx injextors
340lph fuel pump
Welcome to the forum,

If you got the car to idle with one of EFICU's calibrations files then I suggest you dial in the fuel and timing to make sure its running safe until you get properly tuned.

- Ed
Instagram: calibrated.tuning
Mikeyaka23
Posts: 2
Joined: Sun Mar 03, 2024 3:59 pm

Re: K20/k24 flash pro map help

Post by Mikeyaka23 »

Hello Ed,

The calibration file I found searching through the forum posts was set up for an 8th gen SI with a j37 throttle body, Hybrid Cold air intake, and 410cc injectors.

And it seems to start the car fine as the first start-up after completing the engine build. I have the file I am using that I found attached to the post. Can you help with dialing in the fuel and timing?

My setup is:
K20z3 head with k24a bottom end
Drag cartel 3.2 camshafts
K20z3 cam gears I believe they’re 50 vtc
95lb springs and retainers
72mm k tuned throttle body
3 inch short ram cold air intake
K tuned headers
3 inch rev9 exhaust
4 piston Rsx type s oil pump
410cc OEM rdx injextors
340lph fuel pump
Attachments
Bam3292.SD.Rev01 (Blended)(Vtec4600).fpcal
(22.93 KiB) Downloaded 15 times
User avatar
CalibratEd
Posts: 1481
Joined: Fri Feb 07, 2020 3:20 pm
Contact:

Re: K20/k24 flash pro map help

Post by CalibratEd »

I can take a look at it when I have time. Post a datalog of normal driving.

-Ed
Instagram: calibrated.tuning
Post Reply