I need a tuned map for a stock Euro EP3 K20A2. Help please

K-Series Programmable ECU Calibration updates / downloads
zeroprobe
Posts: 8
Joined: Tue Jun 14, 2011 9:47 am

I need a tuned map for a stock Euro EP3 K20A2. Help please

Post by zeroprobe » Tue Jun 14, 2011 9:50 am

Hi,

I've just bought a KPRO and I don't think it comes with a tuned map for a stock Euro EP3 K20A2.

I've searched on here and only see KAL files for EP3's with additional mods.

Would the base calibration ( k20a2-civictyper-tuned.kal ) suit my set up? I notice the VTEC is lowered but the rev limiter is still at 8100.

Can anyone help?

Thanks.

seanyreeves
Posts: 10
Joined: Thu Nov 10, 2011 3:44 pm

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by seanyreeves » Fri Nov 11, 2011 12:27 am

my tuned k20 makes 215whp on the hub dyno, only a header and induction kit. can upload the kal for that if you would like

zeroprobe
Posts: 8
Joined: Tue Jun 14, 2011 9:47 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by zeroprobe » Sun Nov 13, 2011 3:17 pm

Hi,

Sure that be good thanks. Whats the VTEC kick in at?

seanyreeves
Posts: 10
Joined: Thu Nov 10, 2011 3:44 pm

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by seanyreeves » Wed Nov 16, 2011 4:25 pm

lower boundary is 4600 and upper is 6500, it has been tuned by romain levesque at eurospec2000. very reputable tuner.

seanyreeves
Posts: 10
Joined: Thu Nov 10, 2011 3:44 pm

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by seanyreeves » Wed Nov 16, 2011 4:26 pm

see attachement, running open loop as my o2 sensors arent wired in,
Attachments
Normal standard map.kal
(141.67 KiB) Downloaded 535 times

zeroprobe
Posts: 8
Joined: Tue Jun 14, 2011 9:47 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by zeroprobe » Thu Nov 17, 2011 5:17 pm

Thanks,

One quick question, obviously not going to be 100% but would a race header and intake make this map completely unsuitable for a standard EP3?

windspot
Posts: 24
Joined: Wed Feb 13, 2013 12:40 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by windspot » Wed Feb 13, 2013 3:34 am

seanyreeves wrote:see attachement, running open loop as my o2 sensors arent wired in,
my car is wired there, i have to make it closed loop?

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by Nazul » Wed Feb 13, 2013 6:23 am

seanyreeves wrote:my tuned k20 makes 215whp on the hub dyno, only a header and induction kit. can upload the kal for that if you would like
215 whp, i think u mean bhp, not even a s2000 makes 215 whp

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by Nazul » Wed Feb 13, 2013 6:30 am

Why is immobilizer disabled, purge system disabled and ELD disabled?
Did u do a swap?
Then this map is not suitable for other users.

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by Nazul » Wed Feb 13, 2013 6:37 am

Since there is an overal fuel trim of 20%, running this map on a normal setup without header, will result in too rich mixture, fucking your engine on long term, so adapt this to 0.

windspot
Posts: 24
Joined: Wed Feb 13, 2013 12:40 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by windspot » Wed Feb 13, 2013 8:16 am

Nazul wrote:Since there is an overal fuel trim of 20%, running this map on a normal setup without header, will result in too rich mixture, fucking your engine on long term, so adapt this to 0.
can you modify this calibration and upload it so i can load it to the ecu?
im not an expert in this, thats why im asking and i want to thank you for your time and help

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by Nazul » Wed Feb 13, 2013 9:50 am

Yes i can do this tomorrow sorry no k manager installed on windows 8 here at home only at work.

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by Nazul » Thu Feb 14, 2013 1:02 am

Here u go this calibration is adapted for closed loop all sensors on and no fuel trim
Attachments
Normal standard map.kal
(145.09 KiB) Downloaded 369 times

windspot
Posts: 24
Joined: Wed Feb 13, 2013 12:40 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by windspot » Thu Feb 14, 2013 1:09 am

thank you very much!!!
where are you from?
if you come to greece i owe you a drink

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea

Post by Nazul » Thu Feb 14, 2013 1:25 am

Belgium, a little bit too far to just come over ;-)

Post Reply