s300v3 issues with on-board datalog
s300v3 issues with on-board datalog
Issue: Invalid data on on-board datalog files.
Issues began to arise after on-board datalogging was triggered via switched input (service connector) WHILE on bluetooth datalog via Android app. Analog input data is invalid on datalogs from on-board, however when recorded on SManager data is valid. There is also an instance when the all data was invalid (i.e. +300mph).
Tried: Two different laptop's and two ecu's
See attached datalogs and calibration.
Issues began to arise after on-board datalogging was triggered via switched input (service connector) WHILE on bluetooth datalog via Android app. Analog input data is invalid on datalogs from on-board, however when recorded on SManager data is valid. There is also an instance when the all data was invalid (i.e. +300mph).
Tried: Two different laptop's and two ecu's
See attached datalogs and calibration.
- Attachments
-
- 510 test from on board2 invalid data.s3d
- all data invalid on-board datalog
- (1.82 MiB) Downloaded 189 times
-
- 2014-test.skl
- calibration
- (46.12 KiB) Downloaded 171 times
-
- 59 test from smanager.s3d
- smanager datalog
- (354.41 KiB) Downloaded 179 times
-
- 59 test from on board.s3d
- on-board datalog
- (827.89 KiB) Downloaded 173 times
Re: s300v3 issues with on-board datalog
- serial number 30298
- version of software 2.3.2.0
- version of software 2.3.2.0
Re: s300v3 issues with on-board datalog
Followed directions to create new calibration per Javier, and emailed him my new calibration and datalogs....no response. Still having same on-board datalogging issues. Need help as my on-board datalogging feature is not functional.
Re: s300v3 issues with on-board datalog
Your software is not up to date. Download the current version from the downloads section of the website and retest.
Re: s300v3 issues with on-board datalog
Attached calibration and datalog files were pull from SM ver. 2.4.4.0, s300v3 serial number 30298.
Per instruction from Javier and results:
Erased computer, created a new calibration and uploaded to s300, datalogged from SM and on-board to show the issues I'm having. SM datalog checks out fine with all sensors reading correctly however on-board datalog still has false reads on the auxiliary inputs (AN1-7) from what I see. See attachments.
Per instruction from Javier and results:
Erased computer, created a new calibration and uploaded to s300, datalogged from SM and on-board to show the issues I'm having. SM datalog checks out fine with all sensors reading correctly however on-board datalog still has false reads on the auxiliary inputs (AN1-7) from what I see. See attachments.
- Attachments
-
- datalog 7 smanager.s3d
- (174.03 KiB) Downloaded 176 times
-
- datalog 6 on board.s3d
- (172.27 KiB) Downloaded 170 times
-
- NEW_to_fix_datalog.skl
- (41.89 KiB) Downloaded 181 times
Re: s300v3 issues with on-board datalog
The analog inputs display correctly here (AN1 & 2 pressure, AN3-7 temperature).
Hondata
Re: s300v3 issues with on-board datalog
Please look at the attached screen captures of both on board and smanager displays, i.e. Oil Pressure (AN1).
Smanager will datalog both real time and record all sensors+analog inputs correctly (validated reads of temperatures by letting the car warm up and pressures by bliping throttle).
ON BOARD datalog will not record analog inputs correctly (values all erratic, or fixed). Case in point, oil pressure shows 2.4psi....not correct at all. Clearly the on board datalogging function/files are erroneous.
Do I have a faulty s300v3?
Smanager will datalog both real time and record all sensors+analog inputs correctly (validated reads of temperatures by letting the car warm up and pressures by bliping throttle).
ON BOARD datalog will not record analog inputs correctly (values all erratic, or fixed). Case in point, oil pressure shows 2.4psi....not correct at all. Clearly the on board datalogging function/files are erroneous.
Do I have a faulty s300v3?
- Attachments
-
- Capture-smanager datalog.PNG (38.24 KiB) Viewed 12144 times
-
- Capture-on board datalog.PNG (39 KiB) Viewed 12144 times
Re: s300v3 issues with on-board datalog
Ok, thanks for the additional information. We believe we have identified a problem, related to whether the USB is plugged in or not when the vehicle is switched on and the analog inputs. It probably is the cause of the problem you're seeing (it is not your S300).
We'll make up a new software release for testing shortly.
We'll make up a new software release for testing shortly.
Hondata
Re: s300v3 issues with on-board datalog
Software has been release (V2.5.0)
https://www.hondata.com/software
https://www.hondata.com/software
Hondata
Re: s300v3 issues with on-board datalog
Great, hope this resolves the issue.
Re: s300v3 issues with on-board datalog
Smanager 2.5.0.0 did NOT resolve the on-board datalogging issue.
- Attachments
-
- Capture-smanager datalog 2.5.0.0.PNG (37.02 KiB) Viewed 12046 times
-
- Capture-on board datalog 2.5.0.0.PNG (36.54 KiB) Viewed 12046 times
-
- NEW_to_fix_datalog.skl
- (41.89 KiB) Downloaded 175 times
-
- datalog 11 on board.s3d
- (46.29 KiB) Downloaded 161 times
-
- datalog 10 smanager.s3d
- (264.85 KiB) Downloaded 167 times
Re: s300v3 issues with on-board datalog
Your calibration works here. Did you upload to the ECU with 2.5.0 and delete the datalogs?
Hondata
Re: s300v3 issues with on-board datalog
Erased ecu, uploaded calibration, datalog. All on 2.5.0.0. Thoughts?
Re: s300v3 issues with on-board datalog
Did it fix the problem?
Re: s300v3 issues with on-board datalog
No it didn't, on board datalog doesn't work.