Page 2 of 2

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sat Apr 23, 2022 6:29 pm
by EFICU
Yeah it looks really good. I didn't really need to make any adjustments, but I made a couple to tighten things up a bit. I also turned on the rear o2 for this next one, so take it for a spin when you can and we'll see if the rear o2 being on causes any issues.

The pops are not the same pops from pops and bangs tuning. Those come from negative ignition values to cause the pops, your file does not have that done, and I don't do that stuff anyways. It's just how the injectors turn off when you shift, which they do in stock form. The injector values in your calibration are to help it drive a little smoother is all, but they aren't harmful pops.
Dill360.SD.Rev03.1 (Blended)(Vtec4600).fpcal
(23.06 KiB) Downloaded 61 times

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sun Apr 24, 2022 9:13 am
by Dill360
Hey here is the log for today, a 3rd gear pull is closer to the middle this time. Let me know if it gives you the info you need. Car also felt a bit different then the last one (figured has something to do with o2 sensor)

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sun Apr 24, 2022 9:51 am
by EFICU
It looked good for the most part, I didn't see anything too out of place with the sensor on. Some areas trended a little differently, but that could be just the drive. I'll attach the same file but with the sensor turned off, take it for a spin and see if you notice a difference.
Dill360.SD.Rev03 (Blended)(Vtec4600).fpcal
(22.99 KiB) Downloaded 65 times

Re: 2010 si looking for base tune before I get a Hondata

Posted: Thu Apr 28, 2022 2:35 pm
by Dill360
Hey sorry this took a while, there is a lot of traffic on this log as well let me know if I need to do it over. Thanks again!

Re: 2010 si looking for base tune before I get a Hondata

Posted: Thu Apr 28, 2022 8:16 pm
by EFICU
Yeah overall it looks good with or without it turned on. It seems it is a little more consistent with it turned off, but not something to worry about. So in the end, I will provide you two calibrations just so you have them. But it does look as though you can drive it with the sensor turned on which means you will be fine.

Give this one a drive when you can, no rush. I made some minor WOT fuel adjustments is all, we're really close.
Dill360.SD.Rev04 (Blended)(Vtec4600).fpcal
(23.13 KiB) Downloaded 61 times

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sun May 15, 2022 9:39 am
by Dill360
Hey sorry this one took a while. It felt good.

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sun May 15, 2022 4:20 pm
by EFICU
Yeah it looks good. Go ahead and make another datalog when you can and we'll see how it looks. If it looks like this I think we're there for now.

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sat Jun 04, 2022 8:44 am
by Dill360
Hey sorry this took so long again. It felt pretty good is the o2 sensor off or on for this config? Thanks!

Re: 2010 si looking for base tune before I get a Hondata

Posted: Mon Jun 06, 2022 10:05 pm
by EFICU
Looks good, but we had some random knock. Go ahead and make another datalog and let's see if the knock stays or not.

Re: 2010 si looking for base tune before I get a Hondata

Posted: Sun Jun 26, 2022 9:47 am
by Dill360
Hey man , I'm unsure if he heat is causing an issue with the tune or something along those lines under WOT the car sounds a bit funky aswell as a bit of black residue around the exhaust. Ran a really short data log so I did not hurt the car.