Fg2 K20Z3 Need Help with Calibration

FlashPro questions & answers specific to the 2006-2011 Americas Civic Si
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

I just recently got a hondata for my fg2 with a 3” cai, apexi n1 exhaust, and rdx 410cc injectors. Still on my stock injectors due to the RDX ones running like crap when installed, even after adjusting injector size. I’m just using hondatas basemap right now and there seems to be a LOT of knocks. I just need somewhere for a start before I can get dyno tuned.:)
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Attachments
RACEMAP.fpcal
(22.15 KiB) Downloaded 14 times
EFICU
Posts: 3299
Joined: Mon Feb 25, 2019 10:14 pm

Re: Fg2 K20Z3 Need Help with Calibration

Post by EFICU »

Which thread do you want to focus on, this one or your other one?

Where did you buy the RDX injectors from? My concern is they might be fake, which would explain some issues you might be having.
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

I got them from a buddy, they came in honda packaging and im fairly certain they are not fake, could be wrong though.
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Also focus this thread.:)
EFICU
Posts: 3299
Joined: Mon Feb 25, 2019 10:14 pm

Re: Fg2 K20Z3 Need Help with Calibration

Post by EFICU »

Yeah you have a lot of knock going on. Are you hearing knock at all?

What octane fuel are you running?

Are you married to this calibration, or can we use my stuff?

What are your plans for more mods, near future or this is your setup for quite a while?
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

We can use your stuff, i don’t know shit about hondata. Using 91 but could go higher to 94 if i wanted:). I just got hondata so i need a good start.
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

future setup is headers, intake manifold, and throttle body. later down the line though:)
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Also no I don’t hear the knocks at all.
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Don’t mind using your stuff at all, probably better to be honest, haha. This is just some stupid basemap hondata came with and it isn’t doing me very good.
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Also motor mounts are probably a must aswell
EFICU
Posts: 3299
Joined: Mon Feb 25, 2019 10:14 pm

Re: Fg2 K20Z3 Need Help with Calibration

Post by EFICU »

Okay sounds good. Since you have mods planned in the near(ish) future we'll tune it the shorter route for now. Then once you add the mods, if you still want my help we can spend more time on it then. So here is the first one for you. SHoot for 20 minutes on the datalogs, and at least one third gear wide open throttle (WOT) pull from 2500-8600. Then we'll see how it looks.
LakeRace.SD.Rev01 (Blended)(Vtect4600).fpcal
(22.97 KiB) Downloaded 15 times
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Thank you! This map is good for the RDX injectors too correct? If so I’ll put them in now and get a datalog going:)
EFICU
Posts: 3299
Joined: Mon Feb 25, 2019 10:14 pm

Re: Fg2 K20Z3 Need Help with Calibration

Post by EFICU »

No it's not, you said you took them out. Let's see how it looks with the stock injectors, especially since they are already installed. Then you can put the RDXs in and we can see how that looks. I'd like to make sure everything is good with the stock injectors, that way I can tell if the RDXs are fake or have other issues. Either way, this is only good for stock injectors. Once we move to RDXs, I will add that injector info.

Does that sound like a good plan to you?
LakeRace
Posts: 47
Joined: Mon May 16, 2022 8:50 am

Re: Fg2 K20Z3 Need Help with Calibration

Post by LakeRace »

Sounds good, will try right away, just watching last period of the hockey game:)
Post Reply