Hondata

Hondata User Forum
It is currently Sat May 25, 2013 10:52 am

View unanswered posts | View active topics


Board index » s100/s200/s300 » SManager Display Templates

All times are UTC - 8 hours [ DST ]



Post new topic This topic is locked, you cannot edit posts or make further replies.  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
mnjdmek4
 Post subject: A/f gauge problem
PostPosted: Wed Jun 25, 2008 7:33 pm 
Offline

Joined: Tue Sep 25, 2007 4:36 pm
Posts: 15
Location: Minneapolis, MN
Does anyone know if the A/F gauge problem has been fixed yet in the latest version of Smanager?
Top
 Profile  
 
Spunkster
 Post subject:
PostPosted: Thu Jun 26, 2008 9:46 am 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11100
Location: Hondata
There are no known issues with the A/F guague display.
Top
 Profile  
 
mnjdmek4
 Post subject:
PostPosted: Thu Jun 26, 2008 6:08 pm 
Offline

Joined: Tue Sep 25, 2007 4:36 pm
Posts: 15
Location: Minneapolis, MN
Spunkster wrote:
There are no known issues with the A/F guague display.


I get the message "Floating point division by zero" everytime i try to open a A/F ratio gauge in the Display part of Smanager. It keeps popping up non-stop to a point where i have to close it or else it'll freeze my laptop. i have the latest version of Smanager. I'm running Vista. I try to delete the current display files but that doesnt do anything. I even try to get some of the demos that i downloaded here with the A/F gauge and those files open but wont work. is this just a windows vista thing?
Top
 Profile  
 
Hondata
 Post subject:
PostPosted: Fri Jun 27, 2008 9:11 am 
Offline
Site Admin
User avatar

Joined: Thu Aug 15, 2002 12:13 pm
Posts: 5283
Location: Torrance, Ca
In Smanager under Settings try both lambda unit options (air/fuel and lambda).
If you have a calibration loaded then under Closed Loop check the voltage/lambda conversion - none of the air/fuel or lambda numbers on the bottom line should be zero.

_________________
Hondata
Top
 Profile  
 
mnjdmek4
 Post subject:
PostPosted: Fri Jun 27, 2008 8:21 pm 
Offline

Joined: Tue Sep 25, 2007 4:36 pm
Posts: 15
Location: Minneapolis, MN
Hondata wrote:
In Smanager under Settings try both lambda unit options (air/fuel and lambda).
If you have a calibration loaded then under Closed Loop check the voltage/lambda conversion - none of the air/fuel or lambda numbers on the bottom line should be zero.


alrite. got it to work. another hooray for hondata! works awesome.
Top
 Profile  
 
inspector01
 Post subject:
PostPosted: Thu Oct 09, 2008 3:00 am 
Offline

Joined: Thu Oct 09, 2008 2:57 am
Posts: 15
Im having the same problem. I have tried both A/F and Lambda in Settings, and under closed loop, neither the lambda or A/F is 0. Any solutions??
Top
 Profile  
 
VT-Doo
 Post subject:
PostPosted: Thu Oct 09, 2008 4:51 pm 
Offline

Joined: Tue May 09, 2006 2:49 pm
Posts: 107
Location: Stirling, Scotland
I too have the same problem.
I have done as instructed above with no difference.
I've had to re-install SManager twice now. This is the third time it has happened in the matter of hours.

This time it has deleted all my display files too. When I click on "display" I get the error as mentioned above, I click "OK"...I then click on "display" once again to get an error of "can not open file...default.display".
Top
 Profile  
 
Spunkster
 Post subject:
PostPosted: Fri Oct 10, 2008 9:53 am 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11100
Location: Hondata
Download one of the displays from the forum that I have posted and then go to Display at the top and load the display you have downloaded.

The problem must be with how you are setting up the displays.
Top
 Profile  
 
VT-Doo
 Post subject:
PostPosted: Fri Oct 10, 2008 1:16 pm 
Offline

Joined: Tue May 09, 2006 2:49 pm
Posts: 107
Location: Stirling, Scotland
This was with me using a Hondata supplied display. Today I started creating a new display of my own...so far so good.

I don't understand why this problem comes and goes.
Top
 Profile  
 
c1500
 Post subject:
PostPosted: Thu Nov 12, 2009 1:31 am 
Offline

Joined: Fri Nov 06, 2009 2:20 pm
Posts: 4
i also have this problem but am now going to just download a display, but it happened as soon as i put the AF guage in?

_________________
95 civic si, d16z6 I.H.E s300
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic This topic is locked, you cannot edit posts or make further replies.  Page 1 of 1
  [ 10 posts ] 

Board index » s100/s200/s300 » SManager Display Templates

All times are UTC - 8 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 0 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group