Search found 60 matches

by fox30
Tue Jun 15, 2004 1:57 pm
Forum: Non-Hondata
Topic: Compression test 9.5:1 pistons on 84mm bore (2.0L) what psi?
Replies: 0
Views: 1457

Compression test 9.5:1 pistons on 84mm bore (2.0L) what psi?

Anyone know what the correct range of psi I should get with a 9.5:1 compression piston? I was hoping to compare my results with someone in here whos got a good healthy motor.
Thanks
by fox30
Tue Jun 15, 2004 1:53 pm
Forum: s100/s200
Topic: ECT setting is confusing me
Replies: 3
Views: 1770

Thanks for the answer. Its just that its so rich .. when starting up from cold its a bit hard to start and rough idle's till its real warm.. I figured its rough due to the rich value before 172F. Thats why Ive been messing with ECT.. I did get it to start quick and idle smooth at aroind 11.50 on the...
by fox30
Mon Jun 14, 2004 1:03 pm
Forum: s100/s200
Topic: 1000cc injectors controlled by hondata
Replies: 12
Views: 5726

This is when your in open loop? The ecu (in open loop with narrowband o2) should try to calibrate it automatically under 750 mbar right or am i wrong?
by fox30
Mon Jun 14, 2004 12:28 pm
Forum: s100/s200
Topic: ECT setting is confusing me
Replies: 3
Views: 1770

ECT setting is confusing me

Is ECT an additional fuel value on top of the base map until engine warms to 172F? or just an overall setting to adjust fuel according to both hot and cold temperatures? Because my base map is great from 172 -192F But warming up to 172 degrees was very rich ( 10.20 - 10.00 on the wideband ) at a col...
by fox30
Mon Jun 14, 2004 12:01 pm
Forum: s100/s200
Topic: Engine Light comes on sometimes, doesnt matter if in boost
Replies: 11
Views: 4046

Thanks for the tip.. I'll try that.
by fox30
Tue Jun 08, 2004 7:39 am
Forum: s100/s200
Topic: Engine Light comes on sometimes, doesnt matter if in boost
Replies: 11
Views: 4046

nope, it still comes on.. less frequently though and my lambda is usually around 12 so I dont think its mixture related.. Too bad RomEditor doesnt show the error immediatly while datalogging. Like a popup window would be nice with an explanation of code etc.. I have no idea whats triggering this. As...
by fox30
Thu May 20, 2004 9:06 am
Forum: s100/s200
Topic: Engine Light comes on sometimes, doesnt matter if in boost
Replies: 11
Views: 4046

Thanks DaX. I forgot to mention, . I purposely left out the resistor on the wideband install because I am running in open loop and have (under RomEditor / options / Disable 02 Heater) is disabled in my map. Actually ALL error codes are disabled. So it should be ignored right? Otherwise I still am st...
by fox30
Thu May 20, 2004 8:45 am
Forum: s100/s200
Topic: Lambda PLX 250 capacitor / resistor install question
Replies: 5
Views: 2626

No , using the wideband is not heated, so you would need to add one 20ohm 10watt resisor (or 2 '10 ohm' 10 watt resistors in series) to fool the computer to think the heating element is there. Otherwise the check eng light would come on. the wide band doesnt have/use a heating element.
by fox30
Wed May 19, 2004 7:53 am
Forum: s100/s200
Topic: autotune questions
Replies: 9
Views: 5017

lol, I had to read that 3 times
cool thanks for the tip
by fox30
Wed May 19, 2004 7:41 am
Forum: s100/s200
Topic: Engine Light comes on sometimes, doesnt matter if in boost
Replies: 11
Views: 4046

Well if you try to get codes before shutting the car off it wont blink to tell you the codes.. You have to have the jumper in then turn key on to get codes.. as for the other reply, I am running in Open loop, and i just got my PLX Lambda hooked up and its displaying 10.5 - 11.5 mixture.. so It may b...
by fox30
Mon May 17, 2004 1:58 pm
Forum: s100/s200
Topic: Lambda PLX 250 capacitor / resistor install question
Replies: 5
Views: 2626

nevermind I got it:
capacitor 0.1uf - 0.3uf with a minimum of 25Volt rating.
Figured I add it case someone needs to know
by fox30
Mon May 17, 2004 11:41 am
Forum: s100/s200
Topic: Need A ECU Pinout Diagram / ODB0/ODB1/ODBIIa/ODBIIb
Replies: 0
Views: 2986

Need A ECU Pinout Diagram / ODB0/ODB1/ODBIIa/ODBIIb

For ODB0 / ODB1 /ODBIIa / ODBIIb

I found a real good one here:

http://www.hondaswap.com/forums/index.p ... ut+diagram

I hope this link works in here, if not try to cut and paste.
by fox30
Mon May 17, 2004 11:04 am
Forum: s100/s200
Topic: Engine Light comes on sometimes, doesnt matter if in boost
Replies: 11
Views: 4046

Engine Light comes on sometimes, doesnt matter if in boost

hondata s200 with a p28 ECU / B18c1 / turbo / Apex AVC-R boost controller. I dont think the boost controller is causing this but incase someone thinks so I listed it. Sometimes when driving the check engine light will come on either when I am slowing to a stop / acceleration or cruising. Doesn't mat...
by fox30
Mon May 17, 2004 10:55 am
Forum: s100/s200
Topic: Low temperature thermostats
Replies: 11
Views: 29873

lol, that would be cool though! Actually I did see a kit somewhere, maybe summit I forget. That takes full control over your cooling system / electric pump control and thromostat doesnt use a mechanical tempered spring, it opens it as needed electronically. I think the cost for it was in the ballpar...
by fox30
Mon May 17, 2004 10:42 am
Forum: s100/s200
Topic: Lambda PLX 250 capacitor / resistor install question
Replies: 5
Views: 2626

Lambda PLX 250 capacitor / resistor install question

I have read the PLX instructions on both Hondata and PLX Devices web sites and got confused. Hondata talks about adding a resistor into the harness for fooling the ecu. PLX Doesnt mention adding a resistor but talks about adding a noise filtering capacitor. Do I do both? or can I get away with not d...