Search found 30 matches
- Fri Apr 05, 2019 9:31 am
- Forum: K-Pro Calibrations
- Topic: Tuning advice needed on BC Stage 2 K20a for circuit car
- Replies: 4
- Views: 3583
Re: Tuning advice needed on BC Stage 2 K20a for circuit car
Sorry for no replying earlier, sometimes I forgot to check here. You can reach me at me email - wakko.tm@gmail.com - since I check it more often. You want the car to run in Open Loop all the time unless you are going for an endurance race and fuel economy is a key to finish the race in a good positi...
- Thu Mar 28, 2019 8:47 pm
- Forum: K-Pro Calibrations
- Topic: Tuning advice needed on BC Stage 2 K20a for circuit car
- Replies: 4
- Views: 3583
Re: Tuning advice needed on BC Stage 2 K20a for circuit car
The flatness mentioned is because T.Pedal goes to zero, meaning you are lifting your foot from throttle. The spykes are occuring when the ECU goes from closed loop to open loop. A/F is everywhere and closed loop parameters must be better dialed. Since this car is for circuit racing, there are some t...
- Thu Mar 28, 2019 8:08 pm
- Forum: FlashPro Calibrations
- Topic: Tuning Air/Fuel Help 2009 Civic Si
- Replies: 8
- Views: 3768
Re: Tuning Air/Fuel Help 2009 Civic Si
You are using a hybrid calibration with AFM enabled, you need to tune the AFM sensor and not the WOT tables. Its a little bit more complicated to tune and takes more time, but it works just fine. You could just mark the 'Use speed / density tables" under Calibration - Fuel and tune your engine ...
- Wed Dec 12, 2018 3:45 pm
- Forum: Civic Si 2006-2011 Americas
- Topic: Knocks only in cylinder #3. Attached fpcal and data logs
- Replies: 3
- Views: 2782
Re: Knocks only in cylinder #3. Attached fpcal and data logs
Try adjusting spark plugs gap. NGK comes with 1.1 gap from factory, but 0.8 works better (Denso spark plugs have 0.8 from factory if Im not wrong).
- Wed Apr 11, 2018 10:52 am
- Forum: Civic Si 2006-2011 Americas
- Topic: Could someone take a look at this datalog?
- Replies: 3
- Views: 1925
Re: Could someone take a look at this datalog?
A/F is ok, a bit rich at that 2nd gear pull, and S.TRIM is pulling out lots of fuel while in closed loop....I would say there should be some fuel coming out from the exhaust.
Your engine wont get damaged and you can run the basemap forever. But you will see a big difference if you get a custom tune.
Your engine wont get damaged and you can run the basemap forever. But you will see a big difference if you get a custom tune.
- Fri Oct 02, 2015 7:12 am
- Forum: K-Pro Calibrations
- Topic: Projeto para Brasil
- Replies: 2
- Views: 2441
Re: Projeto para Brasil
Check your pm's
- Thu Dec 18, 2014 6:45 am
- Forum: FlashPro Manager
- Topic: FlashProManager v2.2.8
- Replies: 80
- Views: 74531
Re: FlashProManager v2.0.0
Have you checked how the WOT lambda tables are set?
- Wed Sep 03, 2014 11:34 am
- Forum: FlashPro Manager
- Topic: VERSION 1.8.3
- Replies: 3
- Views: 2872
Re: VERSION 1.8.3
You cant downgrade the software just because you cant downgrade the firmware. Have you saved your calibration with version 1.9.3 and upload it again? I don't have this issue with any of the cars I had updated the calibration.
Can you post a datalog and the calibration you are using?
Can you post a datalog and the calibration you are using?
- Fri Jun 06, 2014 10:28 am
- Forum: s300 / SManager
- Topic: NEED HELP TO INSTALL ON WINDOWS 8
- Replies: 15
- Views: 6687
Re: NEED HELP TO INSTALL ON WINDOWS 8
I do....SManager, K-Manager and FlashPro Manager, all working as it should. Check if you have admin permissions and also re-check if you dont have any AV or firewall enabled (even windows 8 firewall or any ther built in Windows security system). I did not had to use compatibility mode to install. Al...
- Tue May 06, 2014 3:17 pm
- Forum: Traction Control with FlashPro
- Topic: Traction Control stopped working
- Replies: 8
- Views: 16784
Re: Traction Control stopped working
I used SManager to try to setup Traction Control. This suggestion I took from this topic: http://www.hondata.com/forum/viewtopic.php?f=43&t=17114&start=15#p74638 - I only used SManager to try to setup TC parameters and see if something different would happen. The datalog I have posted was ma...
- Mon May 05, 2014 5:05 pm
- Forum: Traction Control with FlashPro
- Topic: Traction Control stopped working
- Replies: 8
- Views: 16784
Re: Traction Control stopped working
Ok.... After testing it with almost all the cars that are having this issue, I got nothing. Downloaded TC Manager 1.0.7, got everything setup, saved the calibration, uploaded to TC unit and closed TC Manager window. Unplugged the USB cable for TC and started FP Manager.....and nothing changed. The i...
- Sun Apr 27, 2014 10:04 am
- Forum: Traction Control with FlashPro
- Topic: Traction Control stopped working
- Replies: 8
- Views: 16784
Re: Traction Control stopped working
Traction Control
V1.0.7
Firmware 10
FlashPro Manager
V1.8.2
Firmware 64
V1.0.7
Firmware 10
FlashPro Manager
V1.8.2
Firmware 64
- Sat Apr 26, 2014 12:51 pm
- Forum: Traction Control with FlashPro
- Topic: Traction Control stopped working
- Replies: 8
- Views: 16784
Re: Traction Control stopped working
Forgot to mention:
Flash Pro Manager version 1.8.2
SManager version 2.2.7
I can try something using KManager if that helps you to replicate the problem.
Flash Pro Manager version 1.8.2
SManager version 2.2.7
I can try something using KManager if that helps you to replicate the problem.
- Sat Apr 26, 2014 12:44 pm
- Forum: Traction Control with FlashPro
- Topic: Traction Control stopped working
- Replies: 8
- Views: 16784
Traction Control stopped working
This is happening for a while now.... After updating FlashPro Manager to version 1.8.x, Traction Control stopped working. It simple stopped working as it should and I don´t know what happened.....none of the units are "new installation", it was installed for some time and it was working pr...
- Tue Apr 15, 2014 11:31 am
- Forum: FlashPro Manager
- Topic: no power on flashpro module
- Replies: 28
- Views: 10642
Re: no power on flashpro module
Just checked my customers non BT FlashPro, its working as it should.