Search found 29 matches

by Praylewd powr
Fri Jul 27, 2007 11:54 am
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

thanks for the reply. Any word as to why I would need to alter the tune on my map after I uploaded it onto another p28 ECU with s300? The firmware was the same, etc.....and I was going from a p28 to a p28. It was very strange, not only did I have to change my fuel multiplier, but I also had to alter...
by Praylewd powr
Thu Jul 26, 2007 9:58 am
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

Can you give me a contact name and phone number so I can better explain this issue and/or possible repair/replacement? It would be much appreciated. I would like to resolve this as soon as possible.

Cheers,

Duane
Can
by Praylewd powr
Thu Jul 26, 2007 8:47 am
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

the ecu had the check light error 21 from immediately after I recevied it in the springtime. But since I parked the car from sept to march, I didn't notice the power difference not having vtec. I am embarrassed to say that but the car runs 300ft lbs and my vtec point is 5500rpm so I only lost the fl...
by Praylewd powr
Thu Jul 26, 2007 6:51 am
Forum: s300 / SManager
Topic: attn Hondata: ECU related issue with s300 socketing
Replies: 7
Views: 4560

I posted in the other thread for hondatas attention. The ECU is in fact the issue. Please see the other thread for my post.

Thanks again hondata.
by Praylewd powr
Wed Jul 25, 2007 5:06 pm
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

Well, I lucked out and found another ecu to test on my car. On the way to get it, I checked mine out again...threw the same spool 21 code. Then I swapped his p28/s300 in the car and the spool error is GONE. The vtec engages like it did last season with my s200 on the same ecu. So my only conclusion ...
by Praylewd powr
Wed Jul 25, 2007 12:02 pm
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

Is there a way I could use the same p28 ecu and wire the solenoid up to an aux input? What would that involve? It would save me having to replace the ecu...

Duane
by Praylewd powr
Wed Jul 25, 2007 11:21 am
Forum: s300 / SManager
Topic: attn Hondata: ECU related issue with s300 socketing
Replies: 7
Views: 4560

just bumping the post up from before related to my other post on this same issue. the reply in this post made me think that hondatas recommendation was that disabling the error would not affect the vtec operation. I think I am being told otherwise now, so am curious where I go from here.

Duane
Can
by Praylewd powr
Wed Jul 25, 2007 11:16 am
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

well that is bad news. The issue is (if you look at my previous posts on this spool check error) that the error only occurred after I had my ecu prepped with the s300 and boost control by hondata. It is a p28 that was previously socketed for an s200. Immediately after I received the new s300 in my p...
by Praylewd powr
Wed Jul 25, 2007 9:15 am
Forum: s300 / SManager
Topic: vtec spool error issue with s300
Replies: 11
Views: 11771

vtec spool error issue with s300

I had a previous issue with the spool error code coming up after I had my ecu socketed by hondata. So I have disabled the spool error check in the newer version of smanager but after putting the car on the dyno I am seeing a torque issue that wasn't there before. It appears that the torque is droppi...
by Praylewd powr
Sun Apr 29, 2007 1:00 pm
Forum: s300 / SManager
Topic: Question regarding launch control/boost control/etc inputs
Replies: 1
Views: 1964

Question regarding launch control/boost control/etc inputs

I have been trying a few different things with my s300 and have found the following issues: -using the pinout for the power steering pressure does not work. While datalogging, even with no pin attached, the PSP says ON the entire time. It happens in my buddies s300 also so is this a software glitch?...
by Praylewd powr
Tue Apr 17, 2007 8:18 am
Forum: s300 / SManager
Topic: Boost solenoid mounting location
Replies: 1
Views: 2077

Boost solenoid mounting location

As per my other post, I wanted a followup to this question: I originally had my solenoid mounted behind the pass headlight but moved it closer to the wastegate to shorten the vacuum lines to lower boost creep. It seemed to help a bit, but was wondering if mounting the solenoid by the distributor was...
by Praylewd powr
Mon Apr 16, 2007 11:20 am
Forum: s300 / SManager
Topic: Boost control solenoid issue after install
Replies: 16
Views: 10881

I originally had it hooked up at the manifold but the problem was identical. I then rerouted the lines to shorten them, and ran the source from the comp housing. Same problem. It seems a little better with a higher spring (ie: 10psi spring versus a 7psi spring), but still creeps more than it previou...
by Praylewd powr
Sun Apr 15, 2007 12:31 am
Forum: s300 / SManager
Topic: Boost control solenoid issue after install
Replies: 16
Views: 10881

Boost control solenoid issue after install

I just went from a dual stage manual boost controller to the GM solenoid from hondata with my new s300 (p28). The issue is that while I has very minimal boost creep with rpm increase (2psi increase over 4k-redline)....I am seeing alot of boost creep with the new elec solenoid. I am also noticing int...
by Praylewd powr
Mon Mar 26, 2007 2:34 pm
Forum: s300 / SManager
Topic: attn Hondata: ECU related issue with s300 socketing
Replies: 7
Views: 4560

I must have not updated the smanager. I am sorry for bothering you guys but I must again say kudos to your online response time! It is great. I just downloaded the new version and the disable is right where I thought it should be!

Thanks.
by Praylewd powr
Mon Mar 26, 2007 12:41 pm
Forum: s300 / SManager
Topic: attn Hondata: ECU related issue with s300 socketing
Replies: 7
Views: 4560

How would I do that in smanager?

I look forward to your reply!!

Duane