Search found 24 matches
- Mon Jan 14, 2013 11:36 am
- Forum: s300 / SManager
- Topic: Need ecu obd1
- Replies: 0
- Views: 1587
Need ecu obd1
My ecu died and i have the s300 v2 but ecu burned up so does anybody have one already built for the s300 ?
- Mon Dec 03, 2012 9:41 am
- Forum: s300 / SManager
- Topic: pr4 ecu o2 pinout wich one????
- Replies: 11
- Views: 3741
Re: pr4 ecu o2 pinout wich one????
Any clues anybody?
- Fri Nov 16, 2012 5:37 pm
- Forum: s300 / SManager
- Topic: pr4 ecu o2 pinout wich one????
- Replies: 11
- Views: 3741
Re: pr4 ecu o2 pinout wich one????
lmx o2 kit has a yellow wire for wide band out put signal and a brown wire for narrow band out put i tied the yellow wire to my anologe harness on the s300 then i unpluged the d plug located d14 on the harness side cut it, and hooked up the brown wire (narrow band signal) to d14 (a white wire on the...
- Fri Nov 16, 2012 1:48 pm
- Forum: s300 / SManager
- Topic: pr4 ecu o2 pinout wich one????
- Replies: 11
- Views: 3741
Re: pr4 ecu o2 pinout wich one????
Double checked thats the wire that crashed my system so whats up with that?? is there a step or some thing im supposed to do different ? i have a innovative mtxl set up
- Fri Nov 16, 2012 11:44 am
- Forum: s300 / SManager
- Topic: pr4 ecu o2 pinout wich one????
- Replies: 11
- Views: 3741
Re: pr4 ecu o2 pinout wich one????
got that part wich one is d14 i cut and tied into d14 supposed and it crashed my system had to test tune load ande then reload my map for it to work again, dont think i had the right wire on the harness, you know the specific wire on a pr4 integra ecu?
- Fri Nov 16, 2012 11:10 am
- Forum: s300 / SManager
- Topic: pr4 ecu o2 pinout wich one????
- Replies: 11
- Views: 3741
Re: pr4 ecu o2 pinout wich one????
trying to tie the narrow band signal wire from the wide band o2 to the ecu so it can read the a/f like normal. I have the wide band signal tied to the anologe and have that to data log as well, but the long term and short term fuel trim never do anything i suppose its because i dont have a narrow ba...
- Thu Nov 15, 2012 6:13 pm
- Forum: s300 / SManager
- Topic: pr4 ecu o2 pinout wich one????
- Replies: 11
- Views: 3741
pr4 ecu o2 pinout wich one????
OK looked at diagram for pin out on obd1 ecu looks just like mine. It said d14 o2 signal white wire is there cut it tied it in and bamm crashed my programm had to reboot everything what is the real wire and where??
- Wed Nov 14, 2012 11:14 am
- Forum: s300 / SManager
- Topic: INNOVATIVE LMX WIDEBAND INSTALL
- Replies: 6
- Views: 2863
Re: INNOVATIVE LMX WIDEBAND INSTALL
I read that you have to modifie the board to use d10 th eeld for a wwide band reading? is that just because it only reads sooo much voltage?
- Tue Nov 13, 2012 7:17 pm
- Forum: s300 / SManager
- Topic: smanager real time lamda readings
- Replies: 1
- Views: 1076
Re: smanager real time lamda readings
Does it read anything or read zero? check the voltage on the signal wire to the ecu it should be some where around 0 -7 volts, if you have this check the settings or reload you map hope this helps
- Tue Nov 13, 2012 7:12 pm
- Forum: s300 / SManager
- Topic: INNOVATIVE LMX WIDEBAND INSTALL
- Replies: 6
- Views: 2863
Re: INNOVATIVE LMX WIDEBAND INSTALL
Ok got it done i have a 94 INTEGRA LS pr4 ecu which wire do i cut and tie in the narrow band signal for the ecu o2 The LMX has both out puts
- Fri Nov 09, 2012 6:12 pm
- Forum: s300 / SManager
- Topic: INNOVATIVE LMX WIDEBAND INSTALL
- Replies: 6
- Views: 2863
Re: INNOVATIVE LMX WIDEBAND INSTALL
yes it has 14 to 1 listed on the analog sensor list but up at the air fuel list on o2 reading it does nothing i dont understand exactly what this means
- Fri Nov 09, 2012 4:08 pm
- Forum: s300 / SManager
- Topic: INNOVATIVE LMX WIDEBAND INSTALL
- Replies: 6
- Views: 2863
INNOVATIVE LMX WIDEBAND INSTALL
How do i tie in the wideband signal wire to my s300 v2 i have the analog input harness but do i adjust anything in sensors?
- Wed Jun 20, 2012 11:09 am
- Forum: S300 Calibrations
- Topic: new to s300v2 all 4 injectors stay firing at once why??
- Replies: 5
- Views: 2188
Re: new to s300v2 all 4 injectors stay firing at once why??
yes uploaded one closest to my motor im the one with no live data either you told me to check j12 ect. the only info coming across is an0 through an8 just 0-5 volt references
- Wed Jun 20, 2012 9:09 am
- Forum: S300 Calibrations
- Topic: new to s300v2 all 4 injectors stay firing at once why??
- Replies: 5
- Views: 2188
Re: new to s300v2 all 4 injectors stay firing at once why??
s300 r12 21128 showzone ladson sc did the ecu socket work
- Fri Jun 15, 2012 9:23 am
- Forum: S300 Calibrations
- Topic: new to s300v2 all 4 injectors stay firing at once why??
- Replies: 5
- Views: 2188
new to s300v2 all 4 injectors stay firing at once why??
All 4 injectors fire at same time and stays that after crancking is this a setting or a problem? How do you fix it??