Search found 59 matches

by aceman187443
Tue May 26, 2015 1:22 pm
Forum: K-Pro / KManager
Topic: grounding the cyl head
Replies: 3
Views: 1335

Re: grounding the cyl head

Yeap that's it. I see that it connects at the cyl valve cover stud BUT where does the other end connect to (g101)?
by aceman187443
Tue May 26, 2015 1:18 pm
Forum: K-Pro Calibrations
Topic: k20a basemap or equivelent
Replies: 4
Views: 2907

Re: k20a basemap or equivelent

The only k20a map i see in the new calc menu is a modified map, and it is not in the pnf menu. No base maps for the k20a.
by aceman187443
Tue May 26, 2015 10:23 am
Forum: K-Pro Calibrations
Topic: k20a basemap or equivelent
Replies: 4
Views: 2907

Re: k20a basemap or equivelent

Is a k20a3 OK to start base tuning with?
by aceman187443
Tue May 26, 2015 8:23 am
Forum: K-Pro / KManager
Topic: grounding the cyl head
Replies: 3
Views: 1335

grounding the cyl head

Where is G101 located (so I can ground properly) on the 02 civic si wiring harness??? Thanks a million!
by aceman187443
Mon May 25, 2015 9:24 am
Forum: K-Pro Calibrations
Topic: k20a basemap or equivelent
Replies: 4
Views: 2907

k20a basemap or equivelent

i need a base map for a k20a, i cant find anything close on the "new calibration" menu. is it possible to use a basemap for a k20a2 or k20a3 to get it started up? i would prefer the k20a original basemapping but i cant dig one up anywhere. thanks a million in advance!!
by aceman187443
Wed May 20, 2015 6:24 pm
Forum: s300 / SManager
Topic: nitrous triggrer input?
Replies: 5
Views: 1874

Re: nitrous triggrer input?

That information is incorrect, it is -12 volt (ground) by default, inverted it is +12 volt. Good it has the option to invert input or i would have been running another wire from the engine bay.
by aceman187443
Mon Mar 30, 2015 1:07 pm
Forum: s300 / SManager
Topic: input switch datalogging
Replies: 5
Views: 2322

Re: input switch datalogging

I know its been 2years since I first posted this but I've never been able to trigger the data logging feature of my s300. I have a toggle switch connected to negative ground, then going to the correct pin on the ecu. Should I maybe have a momentary switch instead of a toggle?
by aceman187443
Mon Mar 30, 2015 11:07 am
Forum: s300 / SManager
Topic: nitrous triggrer input?
Replies: 5
Views: 1874

Re: nitrous triggrer input?

OK, is that a 12v positive OR negative input by default?
by aceman187443
Mon Mar 30, 2015 10:07 am
Forum: s300 / SManager
Topic: nitrous triggrer input?
Replies: 5
Views: 1874

nitrous triggrer input?

I want to hookup nitrous on my 93 prelude with s300 (white board) installed on p75 odb1 ecu. I will be using the a/c switch pin (b5) . Is it possible to use the switch in the dash with its existing wiring to trigger "ARM", if I simply set the nitrous input in the smanager to b5, Or do I ha...
by aceman187443
Tue May 20, 2014 10:44 am
Forum: s300 / SManager
Topic: AN1(D12 pin) input ethanol content anylizer
Replies: 15
Views: 4987

Re: AN1(D12 pin) input ethanol content anylizer

Oh and the analog output of the Zeitronix eca display is linear and proportional to the output of the flex fuel sensors signal. Only difference is it has been internally "pulled up" inside the eca to 0-5v. I believe the the correct hookup if you have the eca display and still want to use i...
by aceman187443
Tue May 20, 2014 9:48 am
Forum: s300 / SManager
Topic: AN1(D12 pin) input ethanol content anylizer
Replies: 15
Views: 4987

Re: AN1(D12 pin) input ethanol content anylizer

No I did not they my spare ecu because when I opened it up I seen someone had altered it, rendering it broken for now. I did not try the d10 pin because when reading instructions u seen it says remove OR replace with 1n4038 diode. The key was "or" I think it means "and". So it sw...
by aceman187443
Mon May 19, 2014 9:12 pm
Forum: s300 / SManager
Topic: AN1(D12 pin) input ethanol content anylizer
Replies: 15
Views: 4987

Re: AN1(D12 pin) input ethanol content anylizer

OK, so I've had no success getting the analizer to read properly so I'm going to upgrade to the white board s300. Now my question is before I do it, I see the white board wants the direct wire coming from the flex fuel sensor and a 2.4k ohm resister installed between the 12v pos wire and the sensor ...
by aceman187443
Thu May 15, 2014 9:04 am
Forum: s300 / SManager
Topic: AN1(D12 pin) input ethanol content anylizer
Replies: 15
Views: 4987

Re: AN1(D12 pin) input ethanol content anylizer

Its a Rywire direct jumper harness. It it just a extra length for cutting and splicing into if need be just like stock harness. I purchased directly from Rywire. I have it on a 1993 Honda prelude si 2.3ltr. Sorry I should have been more informative, probably spooked ya when I said jumper harness. Ma...
by aceman187443
Wed May 14, 2014 5:21 pm
Forum: s300 / SManager
Topic: AN1(D12 pin) input ethanol content anylizer
Replies: 15
Views: 4987

Re: AN1(D12 pin) input ethanol content anylizer

I have the zetronics hooked to d12 pin. The output from the zetronics is outputting about .4 of a volt since I have low content enthonal fuel rite now. So yes there is voltage being applied abd read by my fluke multimeter in the vid i attached, I have my jumper harness cut at pin d12 and the zetroni...
by aceman187443
Wed May 14, 2014 3:13 pm
Forum: s300 / SManager
Topic: AN1(D12 pin) input ethanol content anylizer
Replies: 15
Views: 4987

Re: AN1(D12 pin) input ethanol content anylizer

You lost me a little. You mean the large harness that plugs directly into the s300? Why would those inputs have a output? I have my gauges wired to those inputs so I can datalog. Im confused on where to check that voltage at you are asking for.