Search found 62 matches

by OTT
Sun Oct 11, 2009 9:50 am
Forum: s300 / SManager
Topic: EXPORT MOVIE ENHANCEMENT REQUEST
Replies: 1
Views: 1107

bump for Acknowledgement please.
by OTT
Fri Sep 25, 2009 4:46 pm
Forum: s300 / SManager
Topic: EXPORT MOVIE ENHANCEMENT REQUEST
Replies: 1
Views: 1107

EXPORT MOVIE ENHANCEMENT REQUEST

pLEASE, PLEASE, can you add these additional items for Export Movie function:

*Analogue 1 & 2 with custom labels
*MAP
*Launch Control Status
*Anti-Lag status
*SHIFT word for shift light
*AF ratio
*TPS %
*FANC status
*PWM %

?
by OTT
Tue Jul 21, 2009 4:51 pm
Forum: s300 / SManager
Topic: FAO hondata - S300 cb issue
Replies: 4
Views: 2051

software version is 1.4.1.0
by OTT
Mon Jul 20, 2009 1:53 pm
Forum: s300 / SManager
Topic: FAO hondata - S300 cb issue
Replies: 4
Views: 2051

Hondata wrote:C1 is 10 uF, used for power supply smoothing, so is not critical. Unless it was shorted I would not think C1 would cause a problem.
What do you suggest?
by OTT
Sun Jul 19, 2009 3:18 pm
Forum: s300 / SManager
Topic: s300 with p72 automatic ecu
Replies: 4
Views: 2273

its basically an OBD2 ECU with OBD1 style connectors. Hence no location for the S300
by OTT
Sun Jul 19, 2009 3:11 pm
Forum: s300 / SManager
Topic: FAO hondata - S300 cb issue
Replies: 4
Views: 2051

FAO hondata - S300 cb issue

Hi, I have a customer who had purchased a used Hondata (R8 board) and ecu from somone. The datalogging was very occaisionally intermittant and it got to the point where it wouldnt datalog and now gives a RED led. So i have: *tested known good S300-R8 in the ECU. all working no-problems on bench simu...
by OTT
Thu Feb 05, 2009 3:56 pm
Forum: s300 / SManager
Topic: analog inputs with OBD2a/2b Hondata ecus...WHICH PINS?
Replies: 7
Views: 2840

I did look at the link posted above but since ou were telling me one ma not be connected on the ecus with built-in adaptor, I wanted to know from the source if the other was.

I will get one from stock and check it over.
by OTT
Thu Feb 05, 2009 3:42 pm
Forum: s300 / SManager
Topic: analog inputs with OBD2a/2b Hondata ecus...WHICH PINS?
Replies: 7
Views: 2840

D12 definitely built in?

:(
by OTT
Thu Feb 05, 2009 12:28 pm
Forum: s300 / SManager
Topic: analog inputs with OBD2a/2b Hondata ecus...WHICH PINS?
Replies: 7
Views: 2840

spunkster, thanks for the link, it would appear that b6 was not listed at the time.

:?

Hondata the how can i check for certain?

these two inputs are critical for me, I AlWAYS use them for various customers with OBD1 / adaptor harness.
by OTT
Thu Feb 05, 2009 3:19 am
Forum: s300 / SManager
Topic: analog inputs with OBD2a/2b Hondata ecus...WHICH PINS?
Replies: 7
Views: 2840

analog inputs with OBD2a/2b Hondata ecus...WHICH PINS?

I use hondata ecus with OBD2a and OBD2b built in connectors.

I wish to use the OBD1 pin references D12 & B6 on these ECUs, but I need to know which pins to feed them into?

thanks
by OTT
Mon Feb 02, 2009 7:53 am
Forum: S300 Calibrations
Topic: S300 calibration for JUN III cams
Replies: 6
Views: 4785

have you got an email?
by OTT
Wed Jan 14, 2009 10:39 am
Forum: s300 / SManager
Topic: S300 and MSD ignition
Replies: 6
Views: 3748

Your ignition will be stable on high boost or very high rpm compared to stock I use that same setup, MSD6a, blaster coil, msd cap, msd rotor. Ive had this on the car with a built turbo engine for the last 21,000miles no problem, and the car gets abused daily! Ive never seen any issues with it or any...
by OTT
Wed Jan 14, 2009 10:30 am
Forum: s300 / SManager
Topic: s300 problems
Replies: 14
Views: 3949

then get hold of a set of injector nodes and check functionality. Then after that check all positive feeds for injectors and continuity between the injector connectors and the relevant Pins on the ecu. Then go on to check continuity between earth and the earth on each inj. clip. also inspec the sing...
by OTT
Wed Jan 14, 2009 2:22 am
Forum: Romeditor 4 Software
Topic: Software download ROM Editor 4
Replies: 6
Views: 11799

I already use S300 on my own vehicle and on many customers S300 & Kpro. Ive had a bunch of people with S100 & S200's asking me to re-tune their cars since experiencing / talking to customers. Theres only a couple companies who do S100/S200 here and there seems to be alot lacking. Hence My questions.
by OTT
Wed Jan 14, 2009 2:17 am
Forum: s300 / SManager
Topic: s300 problems
Replies: 14
Views: 3949

I would consider having all 4x injectors tested, cleaned the tested since.