Search found 14 matches

by madmazturbo
Tue Apr 28, 2015 2:15 am
Forum: Traction Control with KPro
Topic: speed sensor
Replies: 8
Views: 14798

Re: speed sensor

cheers, i think i have sorted it, basically i have no pin in the eld 15 for my plug. It is part of a hybrid racing adapter, any ideas where i can get a pin from in short notice?
by madmazturbo
Mon Apr 27, 2015 5:02 am
Forum: Traction Control with KPro
Topic: speed sensor
Replies: 8
Views: 14798

Ecu colour connections

Hi Can you assist me a little further for cable colours for the ECU for terminating the traction control please:- traction control cables are :- L+ (red) - (black) ELD (orange) ECU is :- (E connector) 15 ELD - (?) (A connector) 3 IGP1 - (?) (A connector) 5 PG1 - (?) I am fairly certain i could figur...
by madmazturbo
Tue Jun 03, 2014 12:32 pm
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

Saying that your original option from race technology isn't so bad from the link below at £35

http://www.race-technology.com/wiki/ind ... WheelSpeed

This should work reading the specs, what do you think?

Ps threaded version us preferable.
by madmazturbo
Tue Jun 03, 2014 12:24 pm
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

It was the closest characteristics I could find for the race logic equivalent, not a bad plan of yours though to buy one for now.
by madmazturbo
Tue Jun 03, 2014 5:56 am
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

sorry again, I have another question the racelogic sensors are exceptionally expensive so I have attached a link below to the sensors I think will do the job. Can you review and confirm if this ok in your opinion to fit my setup using the hondata traction control please? http://uk.rs-online.com/web/...
by madmazturbo
Mon Jun 02, 2014 2:40 pm
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

Once again you have been really helpful, cheers
by madmazturbo
Mon Jun 02, 2014 7:45 am
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

Cheers for the info, really appreciate it There is a chance the traction control I have ordered from tdi north (England uk) may come with the resisters to go in circuit but just in case I have shown a link below of the resister I think is needed, is this the correct type? http://www.maplin.co.uk/p/m...
by madmazturbo
Sat May 31, 2014 4:02 pm
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

Great cheers. Does it matter from an interference point of view if I run a 12v positive dc supply cable taped together with the two signal cables from the traction control unit for each wheel (I was going to twist these two cable together for each wheel sensor and run a permanent lev with it) Does i...
by madmazturbo
Sat May 31, 2014 7:15 am
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

I have another question, does it matter for the purposes of the traction control to work correctly that that I have 17" wheels on the rear (245 35 17) and 16" wheels at the front (205 45 16)?
by madmazturbo
Sat May 31, 2014 6:08 am
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

Lol, it was meant to be 4 number sensor (4no) 3number wires (3no in short) but you have solved my concerns and have purchased the hondata traction control unit just looking for the sensors now to fit my set up.

Cheers
by madmazturbo
Fri May 30, 2014 2:16 pm
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

Am I right in what your saying that If I have no abs system on my car, I need to take a 12v supply to each sensor as per your diagram and use Hall effect sensors and put 1000 ohm resisters between the 12v supply for the sensor and the positive output of the traction control to the sensor. So I need ...
by madmazturbo
Fri May 30, 2014 6:53 am
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

Re: hondata traction control

cheers

do I connect the 2No signal cables from the traction control system direct to the 2 wires for each sensor or is a 3wire sensor needed with perhaps a separate permanent power supply?
by madmazturbo
Thu May 29, 2014 6:01 am
Forum: General / Traction Control Manager Software
Topic: Sensors for Traction Control
Replies: 10
Views: 19735

Re: Sensors for Traction Control

I will be interested on your outcome as I have just put a post on the forum asking similar questions with traction problems on my k20 engine kitcar. Can you post some pics on how you managed to get the trigger wheel in place and whether you used 2wire sensors in the end and if they just connect onto...
by madmazturbo
Thu May 29, 2014 5:07 am
Forum: Traction Control with KPro
Topic: hondata traction control
Replies: 17
Views: 28446

hondata traction control

Hi I have built a 350bhp rotrex supercharged k20 in a mid engine rear wheel drive 725kg kit car running a kpro management, and have a slight issue with traction in the rain in the dry it holds on fine. I have a quaiffe lsd fitted but no traction control hence these question on how to install it when...