Search found 15 matches

by balla_EG6
Wed Feb 07, 2018 7:26 pm
Forum: FlashPro Manager
Topic: Stock primary O2 vs Analog Wideband Input
Replies: 9
Views: 2507

Re: Stock primary O2 vs Analog Wideband Input

I will try a new O2 sensor.
Must be OEM HONDA ?
by balla_EG6
Wed Feb 07, 2018 2:48 pm
Forum: FlashPro Manager
Topic: Stock primary O2 vs Analog Wideband Input
Replies: 9
Views: 2507

Re: Stock primary O2 vs Analog Wideband Input

At low rpm they seem to show very similar AFRs

The uego sensor is 2" from stock
by balla_EG6
Wed Feb 07, 2018 2:41 pm
Forum: FlashPro Manager
Topic: Stock primary O2 vs Analog Wideband Input
Replies: 9
Views: 2507

Re: Stock primary O2 vs Analog Wideband Input

Power - ign 12v fusebox
Ground - under fusebox (chassis)
Signal - UEGO white wire to ECU B29 EGRL

Voltage offset 0v
by balla_EG6
Wed Feb 07, 2018 4:59 am
Forum: FlashPro Manager
Topic: Stock primary O2 vs Analog Wideband Input
Replies: 9
Views: 2507

Re: Stock primary O2 vs Analog Wideband Input

Sorry... Civic SI 2008 with K24Z block. Invidia header, Injen CAI, ID1000 injectors, 12.5:1 pistons, ethanol. FlashPRO bt
by balla_EG6
Tue Feb 06, 2018 4:11 pm
Forum: FlashPro Manager
Topic: Stock primary O2 vs Analog Wideband Input
Replies: 9
Views: 2507

Re: Stock primary O2 vs Analog Wideband Input

just tought about cheating my WOT target to 0.90 to see if my AEM reads 0.86 ...
by balla_EG6
Tue Feb 06, 2018 4:03 pm
Forum: FlashPro Manager
Topic: Stock primary O2 vs Analog Wideband Input
Replies: 9
Views: 2507

Stock primary O2 vs Analog Wideband Input

Hello guys I have an AEM UEGO attached to B29 (EGR) and configured in closed loop as the wideband input. At logs, I see that past 4000rpm , the stock O2 (corrected) differs from the UEGO a bit. Eg, 0.87 lambda at stock and 0.83 at AEM. No matter what, Hondata uses the Stock O2 for closed loop (even ...
by balla_EG6
Tue Feb 06, 2018 3:39 pm
Forum: FlashPro Manager
Topic: Issue with version 2.9.0.0
Replies: 12
Views: 3052

Re: Issue with version 2.9.0.0

I updated to 2.9.0.0 too, the crank fuel was sent to moon... feels like inj timing was multiplied..
2.9.1.0 works ok again...
by balla_EG6
Wed Sep 03, 2014 3:50 pm
Forum: K-Pro / KManager
Topic: AEM Gauges and Digital Input
Replies: 9
Views: 3732

Re: AEM Gauges and Digital Input

I added the capacitors between ANx inputs and ground, nothing happens.

My ground at head cover is outputting 0.000v and at my trans 0.016v
by balla_EG6
Tue Aug 26, 2014 7:48 pm
Forum: K-Pro / KManager
Topic: E25 - VSS Out - What signal?
Replies: 6
Views: 2772

Re: E25 - VSS Out - What signal?

I mistook, 05-06 has vss out. Im saying that cause I tried everything to make my cluster work without a vss conversion box (using 06+ SI vss with kpro 02-04).
by balla_EG6
Tue Aug 26, 2014 7:39 pm
Forum: K-Pro / KManager
Topic: AEM Gauges and Digital Input
Replies: 9
Views: 3732

Re: AEM Gauges and Digital Input

Will do that.. between AN0 and Analog ground right? I double checked all grounds, seems to be ok. Checked resistance between battery - and chassis, 0.000 ohms. Checked from analog ground and 0.001 . I also tried to check gauges output (0-5v) and voltage seems ok (but I dunno if the multimeter has en...
by balla_EG6
Tue Aug 26, 2014 4:54 pm
Forum: K-Pro / KManager
Topic: AEM Gauges and Digital Input
Replies: 9
Views: 3732

Re: AEM Gauges and Digital Input

I did the jumper from analog ground to an0 1 2 and so on.... The noise stopped...
by balla_EG6
Tue Aug 26, 2014 1:20 pm
Forum: K-Pro / KManager
Topic: AEM Gauges and Digital Input
Replies: 9
Views: 3732

Re: AEM Gauges and Digital Input

I have one in trans, one in head cover. The engine harness is grouding on head cover too.
ok I will do that tonight. The noise should be 0 only on that input or all of them ?
by balla_EG6
Tue Aug 26, 2014 1:17 pm
Forum: K-Pro / KManager
Topic: E25 - VSS Out - What signal?
Replies: 6
Views: 2772

Re: E25 - VSS Out - What signal?

vss out only in auto ecu right ?
by balla_EG6
Mon Aug 25, 2014 8:27 pm
Forum: K-Pro / KManager
Topic: AEM Gauges and Digital Input
Replies: 9
Views: 3732

Re: AEM Gauges and Digital Input

I will review all my grounds (trans, head cover and block). Today I did a new one at my block near the alternator. I did one from kpro frame to battery - . All gauges are grounded at battery - and from there to chassis. Its interesting that stock sensors (map, tps, iat) are ok, but analog inputs are...
by balla_EG6
Sun Aug 24, 2014 8:47 pm
Forum: K-Pro / KManager
Topic: AEM Gauges and Digital Input
Replies: 9
Views: 3732

AEM Gauges and Digital Input

I was using AEM EMS and a full set of AEM gauges. When I did a kswap on my EG6, I moved to HONDATA KPRO but still have my AEM gauges (fuel press, oil press, oil temp, water temp and UEGO). Im getting a lot of noise using 0-5v analog output from them to the analog input ports on kpro. Even on ports t...