I will try a new O2 sensor.
Must be OEM HONDA ?
Search found 15 matches
- Wed Feb 07, 2018 7:26 pm
- Forum: FlashPro Manager
- Topic: Stock primary O2 vs Analog Wideband Input
- Replies: 9
- Views: 2509
- Wed Feb 07, 2018 2:48 pm
- Forum: FlashPro Manager
- Topic: Stock primary O2 vs Analog Wideband Input
- Replies: 9
- Views: 2509
Re: Stock primary O2 vs Analog Wideband Input
At low rpm they seem to show very similar AFRs
The uego sensor is 2" from stock
The uego sensor is 2" from stock
- Wed Feb 07, 2018 2:41 pm
- Forum: FlashPro Manager
- Topic: Stock primary O2 vs Analog Wideband Input
- Replies: 9
- Views: 2509
Re: Stock primary O2 vs Analog Wideband Input
Power - ign 12v fusebox
Ground - under fusebox (chassis)
Signal - UEGO white wire to ECU B29 EGRL
Voltage offset 0v
Ground - under fusebox (chassis)
Signal - UEGO white wire to ECU B29 EGRL
Voltage offset 0v
- Wed Feb 07, 2018 4:59 am
- Forum: FlashPro Manager
- Topic: Stock primary O2 vs Analog Wideband Input
- Replies: 9
- Views: 2509
Re: Stock primary O2 vs Analog Wideband Input
Sorry... Civic SI 2008 with K24Z block. Invidia header, Injen CAI, ID1000 injectors, 12.5:1 pistons, ethanol. FlashPRO bt
- Tue Feb 06, 2018 4:11 pm
- Forum: FlashPro Manager
- Topic: Stock primary O2 vs Analog Wideband Input
- Replies: 9
- Views: 2509
Re: Stock primary O2 vs Analog Wideband Input
just tought about cheating my WOT target to 0.90 to see if my AEM reads 0.86 ...
- Tue Feb 06, 2018 4:03 pm
- Forum: FlashPro Manager
- Topic: Stock primary O2 vs Analog Wideband Input
- Replies: 9
- Views: 2509
Stock primary O2 vs Analog Wideband Input
Hello guys I have an AEM UEGO attached to B29 (EGR) and configured in closed loop as the wideband input. At logs, I see that past 4000rpm , the stock O2 (corrected) differs from the UEGO a bit. Eg, 0.87 lambda at stock and 0.83 at AEM. No matter what, Hondata uses the Stock O2 for closed loop (even ...
- Tue Feb 06, 2018 3:39 pm
- Forum: FlashPro Manager
- Topic: Issue with version 2.9.0.0
- Replies: 12
- Views: 3054
Re: Issue with version 2.9.0.0
I updated to 2.9.0.0 too, the crank fuel was sent to moon... feels like inj timing was multiplied..
2.9.1.0 works ok again...
2.9.1.0 works ok again...
- Wed Sep 03, 2014 3:50 pm
- Forum: K-Pro / KManager
- Topic: AEM Gauges and Digital Input
- Replies: 9
- Views: 3733
Re: AEM Gauges and Digital Input
I added the capacitors between ANx inputs and ground, nothing happens.
My ground at head cover is outputting 0.000v and at my trans 0.016v
My ground at head cover is outputting 0.000v and at my trans 0.016v
- Tue Aug 26, 2014 7:48 pm
- Forum: K-Pro / KManager
- Topic: E25 - VSS Out - What signal?
- Replies: 6
- Views: 2773
Re: E25 - VSS Out - What signal?
I mistook, 05-06 has vss out. Im saying that cause I tried everything to make my cluster work without a vss conversion box (using 06+ SI vss with kpro 02-04).
- Tue Aug 26, 2014 7:39 pm
- Forum: K-Pro / KManager
- Topic: AEM Gauges and Digital Input
- Replies: 9
- Views: 3733
Re: AEM Gauges and Digital Input
Will do that.. between AN0 and Analog ground right? I double checked all grounds, seems to be ok. Checked resistance between battery - and chassis, 0.000 ohms. Checked from analog ground and 0.001 . I also tried to check gauges output (0-5v) and voltage seems ok (but I dunno if the multimeter has en...
- Tue Aug 26, 2014 4:54 pm
- Forum: K-Pro / KManager
- Topic: AEM Gauges and Digital Input
- Replies: 9
- Views: 3733
Re: AEM Gauges and Digital Input
I did the jumper from analog ground to an0 1 2 and so on.... The noise stopped...
- Tue Aug 26, 2014 1:20 pm
- Forum: K-Pro / KManager
- Topic: AEM Gauges and Digital Input
- Replies: 9
- Views: 3733
Re: AEM Gauges and Digital Input
I have one in trans, one in head cover. The engine harness is grouding on head cover too.
ok I will do that tonight. The noise should be 0 only on that input or all of them ?
ok I will do that tonight. The noise should be 0 only on that input or all of them ?
- Tue Aug 26, 2014 1:17 pm
- Forum: K-Pro / KManager
- Topic: E25 - VSS Out - What signal?
- Replies: 6
- Views: 2773
Re: E25 - VSS Out - What signal?
vss out only in auto ecu right ?
- Mon Aug 25, 2014 8:27 pm
- Forum: K-Pro / KManager
- Topic: AEM Gauges and Digital Input
- Replies: 9
- Views: 3733
Re: AEM Gauges and Digital Input
I will review all my grounds (trans, head cover and block). Today I did a new one at my block near the alternator. I did one from kpro frame to battery - . All gauges are grounded at battery - and from there to chassis. Its interesting that stock sensors (map, tps, iat) are ok, but analog inputs are...
- Sun Aug 24, 2014 8:47 pm
- Forum: K-Pro / KManager
- Topic: AEM Gauges and Digital Input
- Replies: 9
- Views: 3733
AEM Gauges and Digital Input
I was using AEM EMS and a full set of AEM gauges. When I did a kswap on my EG6, I moved to HONDATA KPRO but still have my AEM gauges (fuel press, oil press, oil temp, water temp and UEGO). Im getting a lot of noise using 0-5v analog output from them to the analog input ports on kpro. Even on ports t...