In for this too!
Otherwise I will also need to build the APP myself :(
It would be the perfect solution, no need for expensive dashes or a cluster of gauges.
Search found 14 matches
- Thu Jul 02, 2015 10:41 am
- Forum: Hondata Mobile
- Topic: Aux Inputs for display
- Replies: 8
- Views: 6222
- Wed Jul 01, 2015 1:26 pm
- Forum: s300 / SManager
- Topic: [SOLVED] S300 V3 - Analog Inputs not showing voltage.
- Replies: 1
- Views: 1459
Re: S300 V3 - Analog Inputs not showing voltage.
SOLVED - Just updated to the latest beta software and firmware and everything is fine now!!!!
:D
:D
- Wed Jul 01, 2015 10:48 am
- Forum: s300 / SManager
- Topic: Resistance based Temperature Sensor > 0-5v input
- Replies: 10
- Views: 5116
Re: Resistance based Temperature Sensor > 0-5v input
We are using a AEM Pull Up Temp sensor for oil temp has an almost linear output that can easily be corrected if using the 2 extra inputs on the ecu itself that can be calibrated with multiple point. The shortcoming is the slow response time.
- Wed Jul 01, 2015 10:43 am
- Forum: s300 / SManager
- Topic: [SOLVED] S300 V3 - Analog Inputs not showing voltage.
- Replies: 1
- Views: 1459
[SOLVED] S300 V3 - Analog Inputs not showing voltage.
Hello, I've already created a topic about how I will use the analog inputs to build a complete data aquisition system and fail safe using a Hondata S300 V3. It can be found in here: https://www.hondata.com/forum/viewtopic.php?f=19&t=18419 We are currently making all the wiring for the sensors. h...
- Wed Jul 01, 2015 10:25 am
- Forum: s300 / SManager
- Topic: Advanced Protection - More Strategies (quantity, 8 inputs)
- Replies: 23
- Views: 6507
Re: Advanced Protection - More Strategies (quantity, 8 inputs)
Currently our board is entering production, it will use a Arduino to receive the inputs for the extra sensors and will only outup one "master safe" that can be used by the analog inputs "advanced protection". I am facing dificulties with the analog inputs as I can't see any volta...
- Wed May 06, 2015 12:01 pm
- Forum: K-Pro / KManager
- Topic: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
- Replies: 6
- Views: 2090
Re: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
I cannot confirm right now what the wires are. But you can rest assured that the conections are correct and the ground and signal wires also.
The same setup works flawlessly on other Board and Car...
Bit of a mistery, I will dig into it deeper when I retune the car and keep us all informed!
The same setup works flawlessly on other Board and Car...
Bit of a mistery, I will dig into it deeper when I retune the car and keep us all informed!
- Wed May 06, 2015 11:56 am
- Forum: s300 / SManager
- Topic: Advanced Protection - More Strategies (quantity, 8 inputs)
- Replies: 23
- Views: 6507
Re: Advanced Protection - More Strategies (quantity, 8 inputs)
Thanks Forevertrj, that is exactly what we are building. An anxiliary board, receiving all sensors input that will make a single "Advanced Fail Safe" output. Wideband - Hondata already makes this trough the O2 pin ECT - Hondata has this covered in protection It's also a huge disapointment ...
- Tue Apr 07, 2015 11:23 am
- Forum: K-Pro / KManager
- Topic: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
- Replies: 6
- Views: 2090
Re: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
It was my last resort as I couldn't have signal trough the wire on the plug.Hondata wrote:Do not solder the wires to the ECU connectors - you should go through the connector!
The conections are correct, right?
- Tue Apr 07, 2015 11:21 am
- Forum: s300 / SManager
- Topic: Advanced Protection - More Strategies (quantity, 8 inputs)
- Replies: 23
- Views: 6507
Re: Advanced Protection - More Strategies (quantity, 8 inputs)
Thank you very much!
- Tue Apr 07, 2015 7:14 am
- Forum: s300 / SManager
- Topic: Advanced Protection - More Strategies (quantity, 8 inputs)
- Replies: 23
- Views: 6507
Re: Advanced Protection - More Strategies (quantity, 8 inputs)
I would like a defenitive reply, please!
- Tue Apr 07, 2015 7:13 am
- Forum: K-Pro / KManager
- Topic: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
- Replies: 6
- Views: 2090
Re: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
Here is the image of the current setup
Green Wire is signal, yellow is ground.
Green Wire is signal, yellow is ground.
- Mon Mar 23, 2015 4:11 pm
- Forum: s300 / SManager
- Topic: Advanced Protection - More Strategies (quantity, 8 inputs)
- Replies: 23
- Views: 6507
Re: Advanced Protection - More Strategies (quantity, 8 inputs)
Thanks Spunkster, but that does not answer my question.
Is it possible for the hardware of the S300 V3 to do it, it being a software limitation and thus can it be adressed in the future?
Is it possible for the hardware of the S300 V3 to do it, it being a software limitation and thus can it be adressed in the future?
- Sun Mar 22, 2015 4:09 am
- Forum: s300 / SManager
- Topic: Advanced Protection - More Strategies (quantity, 8 inputs)
- Replies: 23
- Views: 6507
Advanced Protection - More Strategies (quantity, 8 inputs)
Hello I'm currently tuning a Honda Prelude with a H22A with a GT3582R. The dattaloging chain I'm building is as follows, and I would like to use the sensor inputs as advanced protections. 1xWideband (can be configured in normaly in protection) 4xEGT's (one per primary) (temp too high = CUT) 1xOil Pr...
- Sun Mar 22, 2015 2:55 am
- Forum: K-Pro / KManager
- Topic: PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
- Replies: 6
- Views: 2090
PRA - Kpro V2 - LM2 - ELD Voltage FLAT 4.5v
Hello, First time with this problem. The ELDv shows flat @ 4.5v and the AFR in the KManager is allways at 2x.x flat (correct with the table), never changes, the output of the wideband doesn't "enter" the software or ECU(?)... Tuning a PRA with a Kpro V2, the LM2 is correctly wired, ELD wir...