Search found 78 matches

by DOHCAccord
Thu Jul 04, 2013 6:05 pm
Forum: s300 / SManager
Topic: AF display not going below 12 or above 19
Replies: 6
Views: 7534

Re: AF display not going below 12 or above 19

i opened the case and the resistors are in place.. how do you recommend removing them from the ecu?
by DOHCAccord
Mon Jul 01, 2013 5:10 pm
Forum: s300 / SManager
Topic: AF display not going below 12 or above 19
Replies: 6
Views: 7534

Re: AF display not going below 12 or above 19

the wideband is the PLX m-300 and is wired into the ecu via the D10 input
by DOHCAccord
Thu Jun 27, 2013 10:20 pm
Forum: s300 / SManager
Topic: AF display not going below 12 or above 19
Replies: 6
Views: 7534

AF display not going below 12 or above 19

Hello,

while datalogging my s300 display will not read below 12 or above 19 for AF.
My wideband will go to as low as 10 before showing rich and 20 before showing lean...

The wideband is accurate but the display will not show the higher or lower numbers...

any ideas on this?
by DOHCAccord
Wed Mar 30, 2011 10:33 am
Forum: s300 / SManager
Topic: Full Throttle Shift
Replies: 1
Views: 1869

its pretty easy to understand and set, record your shifting for say 1/2 2/3 3/4, find the rpm you normally end at, say shift at 8k and it drops to 6500k then set your full throttle shift rpm at 6700k and give it a shot. you can lower or raise it as needed for your shift patterns and preference. dont...
by DOHCAccord
Tue Mar 29, 2011 11:30 am
Forum: s300 / SManager
Topic: does the s300 bypass anything over a stock ecu by default?
Replies: 2
Views: 1698

thats been a thought, but im loading the map as 310cc injectors and it runs perfectly, and i find that h22 injectors are 310 to 345, either way the ecu should run them
by DOHCAccord
Tue Mar 29, 2011 10:27 am
Forum: s300 / SManager
Topic: does the s300 bypass anything over a stock ecu by default?
Replies: 2
Views: 1698

does the s300 bypass anything over a stock ecu by default?

Im trying to fix a car i picked up, 99 hatch with a h22 swapped in it. the car has high impedance injectors, obd1 and will only run on my other cars s300. it will not run on a p13 that came with it. my car has a h22 as well with dsm 450cc and a resistor box. the p13 and my s300 both run my car just ...
by DOHCAccord
Mon Feb 21, 2011 6:48 pm
Forum: s300 / SManager
Topic: pcs/vtec issue, vtec does not engage
Replies: 7
Views: 3305

i may have found the issue. reviewing the basics, the non working datalog is showing the tps at 35% during the entire datalog. wiring is good, car runs fine, so i need to check the voltage and such to figure out why it is only showing 35%
by DOHCAccord
Mon Feb 21, 2011 6:40 pm
Forum: s300 / SManager
Topic: pcs/vtec issue, vtec does not engage
Replies: 7
Views: 3305

datalog pcs not working
by DOHCAccord
Mon Feb 21, 2011 5:27 pm
Forum: s300 / SManager
Topic: pcs/vtec issue, vtec does not engage
Replies: 7
Views: 3305

long datalog, skip to 9 minutes and 8 seconds to see pcs on for the low cam then turn off to engage vtec/high cam
by DOHCAccord
Mon Feb 21, 2011 5:21 pm
Forum: s300 / SManager
Topic: pcs/vtec issue, vtec does not engage
Replies: 7
Views: 3305

1997 Accord F20B DOHC Vtec 450cc dsm injectors PR4 ecu i believe, its a non vtec ecu locash ob2 to obd1 conversion harness pcs used to control relay to activate vtec pcs no longer turns off which in turn activates vtec. datalog one showing car working with pcs turning off activating vtec. one showin...
by DOHCAccord
Sat Feb 19, 2011 3:58 pm
Forum: s300 / SManager
Topic: pcs/vtec issue, vtec does not engage
Replies: 7
Views: 3305

pcs/vtec issue, vtec does not engage

Hello all, Driving the car for 8 months using the pcs output with a relay to engage VTEC. after runing the car for 20 minutes vtec just stopped working. cleaned and inspected all the wiring, relay and solenoid and everything is fine. hooked up my laptop and datalogged driving and the pcs indicator d...
by DOHCAccord
Tue Dec 14, 2010 5:22 pm
Forum: s300 / SManager
Topic: help making my wideband work with eld
Replies: 7
Views: 3359

i found the issue, is the sensor setup, the af was registered as lambda, changed it af and all is well.

thank you all for your help
by DOHCAccord
Tue Dec 14, 2010 4:58 pm
Forum: s300 / SManager
Topic: help making my wideband work with eld
Replies: 7
Views: 3359

yep. everything is just as above
by DOHCAccord
Tue Dec 14, 2010 1:29 pm
Forum: s300 / SManager
Topic: help making my wideband work with eld
Replies: 7
Views: 3359

i have tried disabling eld and not disabling it.
the sensor is set to air fuel
min is 10 max is 20

and when its in the graph or display it reads like lambda .88, 1.06 etc

all i want is it to read 14.89, 12.4 etc so i can start the offset process to ge it to match my wideband display
by DOHCAccord
Fri Dec 10, 2010 8:51 pm
Forum: s300 / SManager
Topic: help making my wideband work with eld
Replies: 7
Views: 3359

help making my wideband work with eld

Ok, heres how it is. plx wideband hooked up, wired up to the eld wire and all works well with the wideband. I have smanager to use eld input for wideband but no matter i change, alter etc my display will not show the af ratio. the graph does nothing either. the only thing that does anything is the e...