Search found 22 matches
- Sat Jun 22, 2019 12:37 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
Got it. I have since started an etune, and am pleased w/results so far. There was a fluctuating, and odd decrease w/ voltage, resulting in my ABS, VSA, SH-AWD CEL coming on. Is there a way to see HP gains other than a dyno?
- Fri Jun 14, 2019 11:17 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
I am installing the deatschwerks 300lph fuel pump, and 600cc injectors with rywire harness. Until I get a tune (in about a week), is it safe to use the flashpro 600cc calibration, with my bolt on's? Its my daily car and I still need to commute for a few days post install. I have: CBE, RV6 DP, ETS TM...
- Mon May 27, 2019 7:08 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
Thank you for your response, gearhead. I didn't push it past the 15.5, and it started tripping my MAP sensor whenever I would be above 4500RPM in 3rd gear. So I just put it back to 2.0. I installed the ETS TMIC this weekend, and haven't really had a chance to see if there have been any noticeable hp...
- Thu Sep 27, 2018 9:26 am
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
I raised it to 2.030, and 2.056, which is (at highest) 15.5psi around 4000-4500 RPM. It is noticeable, but not sure what limits this 2.3L turbo has.
- Fri Sep 14, 2018 5:53 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
does anyone know what the safest psi boost limit would be for the k23a engine of the RDX? Is there an equation to figure this out roughly, or is the only way to know based on dyno read-out?
- Sat Sep 08, 2018 6:21 am
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
And what's the difference between what the sensor can read, and what is safe to boost up to? Also, If I am understanding, the first three RPMs are 1.928, 1.816, and 1.875. if we are at 1 bar constant based on 0 vacuum, does this mean these values in psi are: 13.637, 11.991, and 12.859?
- Sat Sep 08, 2018 5:57 am
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
Would it be beneficial to get the 4 bar hondata MAP sensor? What would this allow?
- Thu Sep 06, 2018 7:01 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
Clearly, this one is not a drawing...and this is just a photo of Target Boost from a stock calibration:
Thanks!- Thu Sep 06, 2018 9:51 am
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
As far as boost goes, my table is very simple and looks like this:
I remember the conversion you directed me to, but I'm confused about how that plays here. It says bar in parentheses, but it can't be 2.0 bar, right? What would be the highest I can have this go to safely.- Fri Aug 31, 2018 2:25 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
Ok, thank you!
- Thu Aug 30, 2018 5:29 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
Another question: as far as cyl in trim, I read that w\forced induction, advancing even a little too far can have quick and bad results. What do you think would be the safest I can advance to w\o having a catastrophic event? But advancing as far as safely possible is desired, ya?
- Thu Aug 30, 2018 2:19 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
As far as knock goes, is 6 in 20-30 min bad in 90*+ ambient temps? And how do I tell if it's actual knock, or not from datalog? I attached, but if it's too much to review I understand. I appreciate all the help I can get! ;-)
- Thu Aug 30, 2018 2:15 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
I thought so, and that's what I'm looking for. Thanks!
- Thu Aug 30, 2018 5:20 am
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
I am also curious about Tplate & Tpedal. I understand what they are, and their correlation, but if I change any of that scaling, will it affect A\F ratios? In other words, can I change the Tplate & pedal %'s and not change the ign\fuel timings? I feel like I am getting more power with my bol...
- Sun Aug 26, 2018 4:54 pm
- Forum: FlashPro Manager
- Topic: 09 RDX base maps
- Replies: 35
- Views: 9401
Re: 09 RDX base maps
I just installed RV6 downpipe, and ATLP cat back ex. I am currently using basemap for "tuned, SRI." I am getting a bit of knock, primarily in cyl #3. I recently, within a 30 min ride of various speeds and RPMs, got only 1 knock for cyl #1 & 2, but 3-5 for cyl #3. The temperature here h...