I am beginning to think my board is defective.. THis never happened w/ my s200..
I"m going to have to find someone who has a s300 board and test it against mine..
Search found 34 matches
- Sat Jun 09, 2007 9:38 pm
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
- Tue May 08, 2007 7:38 pm
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
okay.. I now have my 02 and wideband hooked up on my DP.. on hot starts, it stills runs lean, around 18-19.. for the IAT corr, I had to add about 10% fuel @ 159 degrees, to help bring the AFR's down.. btw, i snipped the analog 1 signal from my LM1 to the ECU harness so it doesn't affect the 02 signa...
- Tue May 01, 2007 6:25 pm
- Forum: s300 / SManager
- Topic: How do you upgrade the firmware? v.1.2.7
- Replies: 2
- Views: 2304
How do you upgrade the firmware? v.1.2.7
as the title states..
How do you do this? it is grayed out in the menu when you run the program..
thanks.
How do you do this? it is grayed out in the menu when you run the program..
thanks.
- Mon Apr 30, 2007 11:50 am
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
i have stock GSR cams and am running in F degrees.. My LM1 wideband is permenantly hooked up and the Analog1 output goes to d14, while analog2 goes to d12.. the analog ground is spliced into the ECu ground wire as well.. WHen hot starting the car, the engine doesn't go lean until the wideband warms ...
- Mon Apr 30, 2007 11:18 am
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
- Mon Apr 30, 2007 11:16 am
- Forum: s300 / SManager
- Topic: Code 9 on turbo h22a
- Replies: 4
- Views: 2807
I had this exact same problem w/ a chipped p06 that I used for s300.. It worked fine for a couple weeks w/ no problems, but began to throw this code every now and then and eventually most of the time.. Sometimes it would result in the enigne stalling and was more of a nusiance.. I finally got tired ...
- Sat Apr 21, 2007 7:53 pm
- Forum: s300 / SManager
- Topic: Apex boost solenoid in place of GM solenoid
- Replies: 4
- Views: 4107
just got back from the track using the gm boost solenoid and boost control I have a 44mm WG w/ a 11 psi spring, gt35r, ramhorn mani and closed dump tube.. set the duty cycle fixed at 25 % and activation @ 10 psi. Boost cut set @ 19 psi.. The solenoid input is tee'd off from the manifold line going t...
- Wed Apr 18, 2007 8:21 pm
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
- Wed Apr 04, 2007 2:26 pm
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
- Wed Apr 04, 2007 12:45 pm
- Forum: s300 / SManager
- Topic: hot start, post start lean problems
- Replies: 22
- Views: 16161
- Tue Apr 03, 2007 12:21 pm
- Forum: s300 / SManager
- Topic: Closed loop and open loop Delima w/ p28 ecu
- Replies: 3
- Views: 2636
- Mon Apr 02, 2007 7:21 pm
- Forum: s300 / SManager
- Topic: Closed loop and open loop Delima w/ p28 ecu
- Replies: 3
- Views: 2636
Closed loop and open loop Delima w/ p28 ecu
Okay, Here's my new problem.. I just switched to a p28 ecu for my s300.. I was using a chipped po6 before and had no problems switching from open loop to closed loop. I am using an Innovative LM1 and have the analog signal hooked up to the ecu inputs for the o2 sensor. and also to the EGR valve inpu...
- Fri Mar 23, 2007 12:14 pm
- Forum: s300 / SManager
- Topic: Where does ECU look when cranking engine?
- Replies: 8
- Views: 4174
- Thu Mar 22, 2007 6:24 pm
- Forum: s300 / SManager
- Topic: Where does ECU look when cranking engine?
- Replies: 8
- Views: 4174
- Thu Mar 22, 2007 12:10 pm
- Forum: s300 / SManager
- Topic: Where does ECU look when cranking engine?
- Replies: 8
- Views: 4174
I'd like to know too.. My car runs real lean for about a minute and has also died out sometimes when I start the eninge after its been off for 10-30 minutes.. my WB shows AFR's in the neighborhood of 17-19.. In the morning when I go start it up, the AFR's are fine and this problem is non existant.. ...