Search found 72 matches

by hiperformance
Thu Mar 20, 2014 1:55 am
Forum: s300 / SManager
Topic: how to power up P28 on bench
Replies: 2
Views: 1045

Re: how to power up P28 on bench

Thank you!
by hiperformance
Thu Mar 13, 2014 1:56 am
Forum: s300 / SManager
Topic: how to power up P28 on bench
Replies: 2
Views: 1045

how to power up P28 on bench

what pins would need power and grounds if I wanted to power up an obd1 p28 on my desk so I can register the s300 online. I have a pig tail to do this with.

thank you.
by hiperformance
Thu Dec 16, 2010 4:28 pm
Forum: s300 / SManager
Topic: Does it make a difference which ECU you use for the S300?
Replies: 15
Views: 4827

Spunkster wrote:I use P72s
Thanks for the answers!
by hiperformance
Wed Dec 15, 2010 8:39 pm
Forum: s300 / SManager
Topic: Does it make a difference which ECU you use for the S300?
Replies: 15
Views: 4827

Spunkster wrote:no
So Spunkster,

If you were given a choice. Which ecu would you prefer to use with the S300?
by hiperformance
Wed Dec 15, 2010 2:48 pm
Forum: s300 / SManager
Topic: Does it make a difference which ECU you use for the S300?
Replies: 15
Views: 4827

Can you record knock with a p28?
by hiperformance
Wed Dec 15, 2010 1:18 am
Forum: s300 / SManager
Topic: Does it make a difference which ECU you use for the S300?
Replies: 15
Views: 4827

so is there any advantage that a p72 has over a p28? spunkster feel free to chime in with a complete answer.

thanks.
by hiperformance
Tue Dec 14, 2010 1:11 pm
Forum: s300 / SManager
Topic: Does it make a difference which ECU you use for the S300?
Replies: 15
Views: 4827

Is that any benefit?
by hiperformance
Tue Dec 14, 2010 12:14 am
Forum: s300 / SManager
Topic: Does it make a difference which ECU you use for the S300?
Replies: 15
Views: 4827

Does it make a difference which ECU you use for the S300?

The question is regarding USDM ecu's and the S300.

Is there any difference between using a P72 or p28? Is there any advantage the p72 has over the p28 or any advantage the p28 has over the p72?

Thanks.
by hiperformance
Fri Feb 26, 2010 1:56 pm
Forum: K-Pro / KManager
Topic: Upload Fail?
Replies: 1
Views: 1048

Upload Fail?

Kpro will not upload? all software is up to date, all drivers are up to date. Even tried removing it and installing it into another vehicle and still upload fail? any ideas?
by hiperformance
Mon Jan 18, 2010 3:12 am
Forum: s300 / SManager
Topic: Please check this datalog.....TPS goes wack in 4th?
Replies: 2
Views: 1253

The length of the data log is interesting. On that particular pass the car ran a 10.9 quarter mile. I had been mentioning to the driver that his shifts were a bit sluggish, I think he is traumatized by bad down shift mishap in the past. On the 1 to 2 shifts, you can actually see the front of the car...
by hiperformance
Wed Jan 13, 2010 2:46 am
Forum: s300 / SManager
Topic: Please check this datalog.....TPS goes wack in 4th?
Replies: 2
Views: 1253

Please check this datalog.....TPS goes wack in 4th?

This datalog was taken during a pass on the drag strip. The car started lunging and running bad for a little bit in 4th then it cleared and pulled strong again. From the point of shifting into 4th the gas pedal was pressed to the floor and never lifted. The datalog shows the TPS fluctuation? startin...
by hiperformance
Thu Nov 19, 2009 1:29 am
Forum: s300 / SManager
Topic: Air fuel runs away at idle?
Replies: 4
Views: 2015

the idle can be tuned perfect, then after a minute of idling, the air fuel runs away and it needs to be returned, changes are made to the fuel table, considerable changes, idles nice then after a minute, the air fuel runs away again. starts idling rough then dies. the wideband is not hooked in the d...
by hiperformance
Sat Oct 03, 2009 3:57 am
Forum: s300 / SManager
Topic: Air fuel runs away at idle?
Replies: 4
Views: 2015

Air fuel runs away at idle?

Just sitting idling smooth at 14:1, the air fuel stays for a bit, then goes to lean, with out touching anything. what would cause that?
by hiperformance
Thu Jan 22, 2009 2:29 am
Forum: s300 / SManager
Topic: HELP PLX INSTALLATION S300
Replies: 2
Views: 2305

I would search the help files or this forum for more in depth information. but.... Go to: parameters, Closed Loop. the wideband lambda table is at the bottom of that page. I believe the voltage/ conversion table is already preset for the PLX. 0v=10 and 5v=20. from there you choose which input source...
by hiperformance
Mon Jan 19, 2009 1:38 am
Forum: s300 / SManager
Topic: error downloading update 1.4.0.0?
Replies: 4
Views: 2090

I used the link you provided, it worked. thank you. I still wonder why it would not automatically update when I went to "help" and "check for updates"? that was a first.