Search found 128 matches

by carbonctr
Tue Apr 03, 2012 11:37 pm
Forum: K-Pro / KManager
Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
Replies: 17
Views: 11691

Re: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????

Dervi wrote:I am an O2 user. Also i want to know about it. Please give me a solution about it. If you tell me a good suggestion then it will be very helpful to me. I am waiting for the suggestion from all of you.
Sorry, I gave up on this a LONG time ago!
by carbonctr
Thu Aug 11, 2011 11:38 am
Forum: K-Pro / KManager
Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
Replies: 5
Views: 1874

Re: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?

Spunkster wrote:It is completely up to you which input you use. ANy input used you will have to cut the wire that goes to the original component for it to work.
Are none of the wires required for the ECU to make the engine run? I don't want to cut wires that will be needed.
by carbonctr
Sun Jul 31, 2011 10:56 am
Forum: K-Pro / KManager
Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
Replies: 5
Views: 1874

Re: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?

retroid wrote:we don't have clutch switch mate (EUDM) but you may install one.
This I know, I just need to know which ECU wire is best to use to wire the one I'm going to fit to.
by carbonctr
Sat Jul 30, 2011 1:55 am
Forum: K-Pro / KManager
Topic: EP3 JRSC High idle when cold
Replies: 2
Views: 1073

Re: EP3 JRSC High idle when cold

All the closed loop fuel trims are positive - this tells us that the fuel tables are too lean. Thank for your reply :-) Any suggestions what I should do to sort this? I am planning to fine tune the calibration by moving my wideband O2 sensor to the front of the CAT and forcing Open Loop. What is th...
by carbonctr
Fri Jul 29, 2011 1:39 am
Forum: K-Pro / KManager
Topic: EP3 JRSC High idle when cold
Replies: 2
Views: 1073

EP3 JRSC High idle when cold

- can't remember serial number, but under 4111 - KManager version 1.5.1.0 - the calibration is attached - a datalog of a problem is attached - Euro EP3 Civic Type-R - PRA Hondata K-Pro - Gruppe-M air intake, JRSC (650 injectors, 3.4 inch pulley, 9psi), Hondata manifold gasket, Mugen header with CAT,...
by carbonctr
Thu Jul 28, 2011 11:33 am
Forum: K-Pro / KManager
Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
Replies: 5
Views: 1874

Re: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?

Spunkster wrote:It is completely up to you which input you use. ANy input used you will have to cut the wire that goes to the original component for it to work.
Does my ECU not require or use any of these inputs for anything else? I don't mind cutting a wire if it isn't required.
by carbonctr
Thu Jul 28, 2011 6:07 am
Forum: K-Pro / KManager
Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
Replies: 5
Views: 1874

EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?

I have a UK EP3 with PRA ECU. I fancy trying the clutch switch for full throttle shifting and was wondering which pin on the ECU is best to use: E16, E22, E29 or B9. My Civic has air con and still has power steering if this makes any difference. Are any of these pins normally used by the ECU or can ...
by carbonctr
Fri Jul 03, 2009 11:11 am
Forum: K-Pro / KManager
Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
Replies: 17
Views: 11691

LK7R wrote:Here are the pictures i have promised. Quality is bad, but I'll take some more later with better light.
Nice one! Thanks for attaching the images. I'll have a go when I have the time and see how it goes....
by carbonctr
Sat Jun 20, 2009 2:38 pm
Forum: K-Pro / KManager
Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
Replies: 17
Views: 11691

No i didn't cut the cables. Just did a proper soldering job on the side of the cables about 3cm away from the conector and isolated them with tape. Will take picture for you. I also used conectors to make it more practical in case i youd need to unplug it or use another WB in my car. You'll see it ...
by carbonctr
Thu Jun 18, 2009 2:02 pm
Forum: K-Pro / KManager
Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
Replies: 17
Views: 11691

I have Innovate Motorsports LC-1 hooked up to my PRA KPRO ECU. I'm using it for WB and NB too. Wiring is as follows (6 wires LC-1 version): ECU conector A: A6 [PHO2S+] - Yellow wire (Narrowband O2 output) A5 [PG1] - Blue wire , Black Wire , Metalic/White wire (Ground - thick black cable) ECU conect...
by carbonctr
Thu Jun 11, 2009 2:32 pm
Forum: K-Pro / KManager
Topic: Innovate LC-1 on Euro CTR with PRA K-Pro
Replies: 5
Views: 3673

You might get a voltage offset when you connect the wideband output to the ELD pin. If so, program the LC-1 to flatline set voltages to calibrate the expected output voltages to the actual voltage the ECU reads. My conversion table looks like this: Actual LC-1 voltage---o2 sensor voltage---AF Ratio ...
by carbonctr
Mon Mar 30, 2009 2:33 pm
Forum: K-Pro / KManager
Topic: Can I copy calibration tables from different ECU type?
Replies: 7
Views: 4083

Spunkster wrote:This is not recommended and may cause some problems as the tables are different and are interpreted didfferently from one calibration type to another.
Thanks for the reply. Maybe best to avoid the table copying.
by carbonctr
Sun Mar 29, 2009 2:52 pm
Forum: K-Pro / KManager
Topic: KManager 1.3.5.4
Replies: 25
Views: 12890

Whenever I download the update using the link in this thread my AVG scanner throws up a virus warning stating there is a virus with the new .exe file. The virus is Win32/Virut.Z Anyone else get this? I have AVG but recently reinstalled with the latest download. I think I did get the same warning be...
by carbonctr
Sun Mar 29, 2009 2:43 pm
Forum: K-Pro / KManager
Topic: Can I copy calibration tables from different ECU type?
Replies: 7
Views: 4083

Interesting...I never tried opening a calibration with notepad...I never thought it would just be a text file. Cheers for the info!
by carbonctr
Sat Mar 28, 2009 2:50 pm
Forum: K-Pro / KManager
Topic: is there a way to make a sound for shifting
Replies: 9
Views: 2722

spider00rr wrote:still can't get it to work am I doing something wrong ?
Have you managed to get it working yet?