here's my map, its a rough tune, only low load got tuned before I had other issues on the dyno.
t3/67mm turbo
id1000 injectors
omni 4bar map
ge intake manifold
70mm tb
base fuel around 50psi
Search found 53 matches
- Tue Apr 16, 2013 9:20 am
- Forum: S300 Calibrations
- Topic: ID1000cc Injectors H22a Turbo
- Replies: 1
- Views: 2612
- Wed Jul 11, 2012 8:59 pm
- Forum: S300 Calibrations
- Topic: H22 turbo passed emisssions
- Replies: 1
- Views: 2810
Re: H22 turbo passed emisssions
updated, rebuilt and running again...
- Thu Jun 16, 2011 7:41 pm
- Forum: s300 / SManager
- Topic: H22a VTEC Spooling Issue
- Replies: 1
- Views: 1915
Re: H22a VTEC Spooling Issue
post your calibration,
fuel reg. vac line?
fuel reg. vac line?
- Thu Jun 16, 2011 9:07 am
- Forum: Coil Pack Retrofit
- Topic: Coil Pack Retrofit
- Replies: 88
- Views: 433676
Re: Coil Pack Retrofit
would it be possible to elimate distributor on a h22,
using obd2 oil pump/crank sensor
but you still need the cylinder postions sensor in dizzy?
using obd2 oil pump/crank sensor
but you still need the cylinder postions sensor in dizzy?
- Thu Jun 16, 2011 8:40 am
- Forum: S300 Calibrations
- Topic: H22 turbo passed emisssions
- Replies: 1
- Views: 2810
H22 turbo passed emisssions
walbro 255 id1000 .82ar 67mm t3 3inch down, ceramiac high flow no name cat, vibrant ultra quiet resonator, big magnaflow muffler synapse turbo h22 manifold, heat wrapped mani, down, and wrapped the cat too. no egr, purge, iacv, fitv. golden eagle im shell 91 fresh oil cut it really close, Nox limit ...
- Mon Jun 13, 2011 4:07 pm
- Forum: S300 Calibrations
- Topic: Piston change - Need help adjusting my turbo basemap
- Replies: 8
- Views: 6331
Re: Piston change - Need help adjusting my turbo basemap
when you go to make changes to your fuel tables, be sure you are looking at the fuel table and not the timing map. there is a high speed timing, low speed timing high speed fuel , low speed fuel the difference bewteen high and low speed map is vtec in vtec is high not in vtec is low just wanted to m...
- Mon Jun 13, 2011 3:57 pm
- Forum: S300 Calibrations
- Topic: Piston change - Need help adjusting my turbo basemap
- Replies: 8
- Views: 6331
Re: Piston change - Need help adjusting my turbo basemap
is there anything i can do for the idle? do you just adjust the cells that it sits on when idling, and keep reducing fuel until it idles at 14.7? thanks :) thats exactly what i do, just be sure its at operating temp, i like to set up the coolant temp compensations, and air intake compensations in t...
- Mon Jun 13, 2011 11:51 am
- Forum: S300 Calibrations
- Topic: Launch control "popcorn" ?
- Replies: 3
- Views: 11951
Re: Launch control "popcorn" ?
I haven't done it but, I have read that it is from adjusting the values so it's rich and timing retarded. so when charge ignites, it flames out of the combustion chamber, to help spool big turbo. this can be potentially dangerous cause of the increase in exhaust gas temp in exhaust ports, manifold, ...
- Mon Jun 13, 2011 11:30 am
- Forum: S300 Calibrations
- Topic: Piston change - Need help adjusting my turbo basemap
- Replies: 8
- Views: 6331
Re: Piston change - Need help adjusting my turbo basemap
http://i1121.photobucket.com/albums/l504/megomaniac1/Untitled.jpg -table showing is fuel value table for low speed map, this is the table you need to adjust to add or remove fuel. -you can also view recorded lambda values, upside down "Y" symbol what i do is select the the cells i want to...
- Sun Jun 12, 2011 9:17 pm
- Forum: S300 Calibrations
- Topic: Piston change - Need help adjusting my turbo basemap
- Replies: 8
- Views: 6331
Re: Piston change - Need help adjusting my turbo basemap
If you can, wire up the 5v from your wideband to datalog with ecu. use the offset voltage to get reading to match your gauge if you need to. then you can review your data logs, and make adjustments as nessary. what I do is look at the estimated %change table, and recorded a/f table, and just tweak i...
- Sat Jun 11, 2011 9:29 am
- Forum: S300 Calibrations
- Topic: Piston change - Need help adjusting my turbo basemap
- Replies: 8
- Views: 6331
Re: Piston change - Need help adjusting my turbo basemap
rent a trailer. Closed loop doesn't work well, until the open loop maps are close to tagert a/f ratio. you need to run your car in open loop, watching your wide band, set your idle and adjust the map + or - to get to 14.7 a/f. keep an eye on display as well, cause the coolant compensations are going...
- Wed May 25, 2011 5:38 pm
- Forum: S300 Calibrations
- Topic: H22A 15 psi 1000cc injectors
- Replies: 24
- Views: 64824
Re: H22A 15 psi 1000cc injectors
maybe if you post a bigger picture, you'll get more replys...
- Wed Nov 03, 2010 6:11 pm
- Forum: s300 / SManager
- Topic: Program to change RPM and Load indexes from S300 calibration
- Replies: 16
- Views: 10898
- Sat Sep 25, 2010 10:09 am
- Forum: s300 / SManager
- Topic: 1998 prelude SH with S300
- Replies: 3
- Views: 3091
- Sat Aug 14, 2010 10:41 am
- Forum: S300 Calibrations
- Topic: h22 turbo map work in progress
- Replies: 2
- Views: 2957
I won't get a chance to drive it for a while, out of province working. I think I have some other things to figure out before more tuning. need to confirm what map sensor I have, It's a onmi, but could be anything from a 2.5 to a 4, not 100% sure, I think it might be a 3bar, came with the TB i bought...