Search found 14 matches
- Tue Sep 09, 2008 6:17 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
- Tue Sep 09, 2008 3:33 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
- Tue Sep 09, 2008 2:12 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
- Fri Sep 05, 2008 5:02 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
- Fri Sep 05, 2008 12:17 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
- Thu Sep 04, 2008 5:18 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
ok so I'm sitting in my car and been trying to get hondalogger to connect to my ecu. All I keep getting is connection error. I've been trying for a while now and I have the correct COM port set. Every once in a while it says it connected but when i start the car it doest monitor anything and when I ...
- Tue Sep 02, 2008 7:29 pm
- Forum: s100/s200
- Topic: boost option problems
- Replies: 12
- Views: 8537
boost option problems
ok so I went and had my car tuned today with my s200. Before going to get tuned I emailed Hondata and had the options checked against my serial number and I have Boost and Data logging. My tuner used his interface box and other needed equipment to tune and burn map. Once I test drove the vehicle aft...
- Mon Aug 18, 2008 11:55 am
- Forum: Romeditor 4 Software
- Topic: connecting to ECU
- Replies: 3
- Views: 15983
- Mon Aug 18, 2008 11:17 am
- Forum: Romeditor 4 Software
- Topic: connecting to ECU
- Replies: 3
- Views: 15983
connecting to ECU
I need to burn a basemap since I just install my JRSC with 575cc injectors. Do I connect to my ecu from laptop through the datalogging port on my blue interface box. I have a s200
- Sat Aug 02, 2008 8:55 am
- Forum: HondaLogger Software
- Topic: connection question
- Replies: 1
- Views: 14249
connection question
I installed my ODBI P28 ecu with conversion harness yesterday and my Hondata s200. The car starts up and runs fine for the most part (runs very rich and no power but figured its because of not being tuned) however I can not get my laptop to connect to my interface box. While the ignition is turned o...
- Fri Aug 01, 2008 8:00 pm
- Forum: s100/s200
- Topic: s200 data logging
- Replies: 8
- Views: 6468
ok so I got my odb2 to odb1 conversion harness in today and went to install my s200. Once everything was hooked up the car starts and runs but I get a slow blinking LED on the interface box (stays on in between blinks). I have a D9 to USB cable to connect to my laptop. I cant seem to get Hondalogger...
- Sat Jul 26, 2008 4:49 pm
- Forum: s100/s200
- Topic: s200 data logging
- Replies: 8
- Views: 6468
- Fri Jul 25, 2008 5:29 pm
- Forum: s100/s200
- Topic: s200 data logging
- Replies: 8
- Views: 6468
- Fri Jul 25, 2008 4:25 pm
- Forum: s100/s200
- Topic: s200 data logging
- Replies: 8
- Views: 6468
s200 data logging
I just purchased a s200 system that has boost and data logging, however the seller did not send me the data logging cable to connect to my laptop. Can I use any serial cable or did I need a special cable from hondata? Also I know we arent suppose to post about this but I did email support with my se...