Search found 15 matches

by A4XRBJ1
Mon Jun 22, 2009 11:22 pm
Forum: K-Pro / KManager
Topic: S2000 750rc's soaking in gasoline when starting
Replies: 5
Views: 1847

Spunkster wrote:YOu will have to try different values until it resolves the issue.
The answer I was more looking for is something like "You have to try the biggest negative value where the car will fire up immediately" or so. You're is rather obvious
by A4XRBJ1
Mon Jun 22, 2009 10:45 am
Forum: K-Pro / KManager
Topic: S2000 750rc's soaking in gasoline when starting
Replies: 5
Views: 1847

You can reduce the cranking fuel to fix this, but normally just adjusting the injector size will take care of the cranking fuel, so there may another problem. What are your fuel adjustments from the 'fuel trim' page? Hi, I do not have any fuel adjustments overall, everything is set to 0%. My tuner ...
by A4XRBJ1
Fri May 22, 2009 3:01 am
Forum: K-Pro / KManager
Topic: S2000 750rc's soaking in gasoline when starting
Replies: 5
Views: 1847

S2000 750rc's soaking in gasoline when starting

Hi, my car and tuning is fine, making 436hp @ 8333 rpm on a Honda S2000, so that's great. Only problem that exists is that the injectors (RC 750's) are shooting way too much gasoline in when the car is started. It smells gasoline immediately and I'd two occasions now when the sparks got so wet when ...
by A4XRBJ1
Wed Apr 15, 2009 1:01 pm
Forum: Applications
Topic: How can I connect the PLXDevice Bosch LSU4.2 WB to Hondata?
Replies: 5
Views: 4599

Thanks Spunkster, that solved it.

Andreas
by A4XRBJ1
Wed Apr 15, 2009 11:47 am
Forum: K-Pro Calibrations
Topic: Running extremely lean when started 1:18 - 1:20
Replies: 1
Views: 1688

Running extremely lean when started 1:18 - 1:20

Hi, finally got it and connected my PLX device wideband sensor to the Hondata through ELD. Changed it in the software under settings, wideband input to PLX M Series on the quick select. Numbers are displayed correctedly, in accordance to what the PLXdevice display says. Now comes the problem. After ...
by A4XRBJ1
Wed Apr 15, 2009 7:19 am
Forum: Applications
Topic: How can I connect the PLXDevice Bosch LSU4.2 WB to Hondata?
Replies: 5
Views: 4599

There are no special insturctions, tools or plugs required. You simply input the wideband signal from the PLX into the ELD input making sure that you have disconnected the ELD wire from the ELD. Hi Spunkster, I'm still lost as I do not know where to cut the cable. It says D10 so I assume you mean P...
by A4XRBJ1
Wed Apr 08, 2009 3:59 pm
Forum: K-Pro / KManager
Topic: Low battery voltage reason for slow starting engine?
Replies: 1
Views: 1180

Low battery voltage reason for slow starting engine?

Hi guys, I love the Hondata (now that I finally figured out to datalog :) ) I've uploaded both my .cal and my log file of me trying to start the engine cold. As you can see from the log I only have 11.7V when I turn the ignition on (seems pretty low) and it goes down to 9.9V when I press the start b...
by A4XRBJ1
Wed Apr 08, 2009 3:25 pm
Forum: K-Pro / KManager
Topic: Read button on Knock/TPS are not enabled!
Replies: 5
Views: 1881

Spunkster wrote:You must be datalogging fo rthem to be able to read.
Blush, ok, now I'm smarter. Problem solved. What still puzzles me, I've got a negative reading for the minimum. I though 0 volt was the only possible minimum?


Thanks Spunkster,

Andreas
by A4XRBJ1
Wed Apr 08, 2009 3:20 pm
Forum: KManager Display Templates
Topic: 800x480 displays
Replies: 1
Views: 8487

Hey Carbonctr,


nice display, thanks for the effort!

One question, as I use Kp/h instead of mph, will it work on my Hondata too or do you have to change the display for kph?


Andreas
by A4XRBJ1
Wed Apr 08, 2009 3:09 pm
Forum: Applications
Topic: How can I connect the PLXDevice Bosch LSU4.2 WB to Hondata?
Replies: 5
Views: 4599

How can I connect the PLXDevice Bosch LSU4.2 WB to Hondata?

Hi, I know it needs to be connected to the ELD port(?), but are there instructions available of how to solder it or is there a special connector available? My PLXDevice has the wideband signal running out through a connector which I could connect directly with my old Greddy e-Manage Ultimate. Can th...
by A4XRBJ1
Wed Apr 08, 2009 2:57 pm
Forum: K-Pro / KManager
Topic: No data shown in Graph windows/Display window
Replies: 1
Views: 1199

No data shown in Graph windows/Display window

Hi,

second problem. Wanted to check the sensors while my engine is running, but no data at all is shown at the Graph windows and neither at the Display windows.

On-board Datalogging is not enable in the parameter windows. Engine is running and KManager is connected.


TIA,

Andreas
by A4XRBJ1
Wed Apr 08, 2009 2:54 pm
Forum: K-Pro / KManager
Topic: Read button on Knock/TPS are not enabled!
Replies: 5
Views: 1881

Read button on Knock/TPS are not enabled!

Hi, I started my engine today for the first time with the Hondata, first start was ok but after a couple of starts it takes about 5-7 seconds to start. I wanted to check if my TPS settings are right, but I can't click on the read button as both are constantly disabled. Please note that I'm connected...
by A4XRBJ1
Mon Apr 06, 2009 3:25 pm
Forum: K-Pro Calibrations
Topic: 14 PSI S2000 with Vortech sc needs cal
Replies: 3
Views: 2386

You will need to fully tune this on the dyno to make sure your AF ratio is correct and tune for correct ignition timing to be safe. Hi Spunkster, that's planned for the 17th of April with the Belgium Hondata Dealer and Tuner. As I'm an AP1 (forgot to tell) I probably have to start from the stock AP...
by A4XRBJ1
Sun Apr 05, 2009 3:18 pm
Forum: K-Pro / KManager
Topic: KManager 1.3.5.4
Replies: 25
Views: 13022

CreateProcess failed; code 5.

I've update from 1.3.4 which installed seamlessy. Check online and downloaded directly from the web the new version. When it installed and restarted, I got the above error message from AVG8. Now when I want to restart the program I get the following error box: Unable to execute file: C:\Program File...
by A4XRBJ1
Sat Apr 04, 2009 9:47 am
Forum: K-Pro Calibrations
Topic: 14 PSI S2000 with Vortech sc needs cal
Replies: 3
Views: 2386

14 PSI S2000 with Vortech sc needs cal

Hi guys, I'm new here as I just about to switch from a Greddy e-manage Ultimate to Hondata (ok, hit me for not switching earlier). Anyway, I'm about to get the Hondata installed and was just asking if someone has experience with the combination of Hondata K-Pro and a Vortech supercharger on a S2000....