Hondata

Hi, I was wondering if I can get a cal for a 2004-2006 TSX reflash... Thanks in advance.

Kpro serial number: 37820-PRB-305 2054-100569 Kmanager: v1.3.7 Vehicle: Acura TSX I tried to add abit more fuel to cool it down but that didnt work either... The ECT fluctuates around 180-185 in the day (80-85F) and at night 177-185 (68-75F). The outside temp was measured using the car's thermostat...

Im running a dual K-Pro on the TSX also and had rough idling... I set the low speed fuel col 3 and 4 / 750 and 1000 at 748 (running about 12-13:1 AF) and the rough idling disappeared... With the AC on there alittle bit of vibration but thats about it... I have a 5AT though and running w/o FI... Some...

I dunno if K-Pro has anything to do with this, but the fans on the radiator turns on and stays on after 2-3 minutues of idle... Before it used to turn on and off but it stays on until I turn the ignition off...

So I am assuming that I should try to tune my idle AF ratio in open loop mode to be 13.1? Also, I've heard that I should keep increasing ignition at idle. What is an unsafe ignition value at idle? How high can I push it? Right now I believe I have it at 25 degrees. I was going to try to play with t...

No stalling, but it feels its like its about to stall when it dips below 400-500rpms... Sometimes the idle becomes stable after time but now with this new calibration, it rarely goes away... When I first got the K-Pro, it was fine until one day the rough idling came about... So I installed the O2 re...

I also have the same problem where the idling is not stable... Is your car stalling/shutting off? What injectors are you running? Im running stock injectors... I have an auto and in "D", instead of the idle being 600 it fluctuates either from 750 to 600 constantly or dips down below 500 a...

I recently got a dyno tune from a shop and I forgot to ask the tuner to give me a copy of the calibration... I was wondering if I can get that calibration somehow by hooking my own cpu to it... I'm guessing if you connect the cpu and interface with it by pressing F10, does that reflect the current c...

I also have the same problem where the idling is not stable...

I did a datalog and came up with 81 knocks pulling on 3rd gear (even though the kmanager says 4th)... How do I go about fixing this because it looks like its running alittle rich at 11-12:1... Do I add fuel to that to make it close to 14??? Also, the VTC is supposed to advance to 45 degrees but it o...

I disconnected/reconnected the battery and now the error code is gone... :)

It seems like its on and off with the error code. I would turn the car off all the way, plug it in and sometimes its there and some time its not... I did this about 7-8 times and about half of the times it would throw an error and the other half no...

Thank you for your response. I guess the kal loaded once reloaded and I unplugged and replugged and it still gives me the error code but now the kmanagement actually gives me a reading back for the angles. I have one more question... I did some datalogging and the VTC wont go past 26 degrees... I am...

I was looking through a couple of different SC kits for the TSX and I seen a dyno on the page saying the hondata's RSX was tuned with this same kit. From your experiences, would this kit have major fitment problems with the TSX? Also, it says the air condition compressor has to be removed. Would the...

I recently installed a machined VTC in the motor and when I plugged in the laptop to the ECU, this error code came up... http://farm4.static.flickr.com/3355/3551411791_185c5e62e9.jpg?v=0 Would one of the reasons be the sensor wasnt properly installed correctly or did it really go bad? Also when I tr...