Search found 20 matches

by wiggum80
Mon Jul 30, 2018 12:13 pm
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Nitrous Control
Replies: 1
Views: 988

Nitrous Control

Is there anything in the software that can control nitrous?
The ethanol content input works off 5v, can that possibly be used?
by wiggum80
Mon Jul 04, 2016 9:25 am
Forum: Civic Si 2006-2011 Americas
Topic: Overrun throttle opening enabled checkbox not present
Replies: 1
Views: 985

Overrun throttle opening enabled checkbox not present

The 06-11 Civic Si has some basemaps with a checkbox for "Overrun throttle opening enabled" and some without. I prefer to use Map based calibrations to start from because a lot of cold air intakes have the MAF sensor before the breather tube to the valvecover. Using a MAF based basemap wouldn't work...
by wiggum80
Mon Dec 21, 2015 12:01 pm
Forum: TSX 2004-2014
Topic: Looking for an output source
Replies: 1
Views: 4190

Looking for an output source

Working on a k series Honda Fit that uses the 07-08 TSX ecu with a Flashpro. The Car has a surge tank with 2 fuel pumps. I want to use 1 pump on the regular fuel pump circuit and the other to kick in when boost comes on. Reason being is the fuel temp gets too high idling with 2 pumps on. I've done t...
by wiggum80
Wed Nov 26, 2014 10:06 am
Forum: s300 / SManager
Topic: Datalogging extra sensors
Replies: 2
Views: 1564

Datalogging extra sensors

I was looking at purchasing a few extra sensors for a car I'm working on and was wondering the best way to go about setting them up to datalog in the S300. -Fuel pressure and Oil pressure (both will use AEM 0-150 psi pressure sensors) -Rear wheel speed (will use the xenocron rear wheel speed sensor ...
by wiggum80
Thu Oct 30, 2014 7:13 am
Forum: s300 / SManager
Topic: AEM wideband input
Replies: 2
Views: 1514

AEM wideband input

Which input pin works the best when datalogging the AEM wideband gauge? I've been using D14 ( stock 02 input) on many cars I tune but have heard the ELD pin may work better. Anyone have any thoughts or reasons one may work better than the other?
by wiggum80
Thu Oct 30, 2014 7:10 am
Forum: s300 / SManager
Topic: S300 repairable?
Replies: 2
Views: 1267

Re: S300 repairable?

Email sent, thank you.
by wiggum80
Wed Oct 29, 2014 6:22 am
Forum: s300 / SManager
Topic: S300 repairable?
Replies: 2
Views: 1267

S300 repairable?

Car was recently pulled from storage, fuel pump won't prime and solid CEL. A different ECU/s300 and the car runs perfect. Faulty Hondata s300 ser# 12194. ECU tests ok on a moates Engine simulator, ECU is a 37820-P06-A01. When uploading the s300 on the moates engine simulator you can upload and datal...
by wiggum80
Wed May 07, 2014 1:06 pm
Forum: s300 / SManager
Topic: Latest S300 (silver board) Compatibility
Replies: 1
Views: 720

Latest S300 (silver board) Compatibility

I have an ecu with a first generation S300 (green board), if I purchase a new S300 (silver board) will I have to make any changes or will it drop right in without any modification?
by wiggum80
Tue Aug 14, 2012 11:12 am
Forum: K-Pro / KManager
Topic: Fuel table #s max out at less than 50% duty cycle
Replies: 1
Views: 1047

Fuel table #s max out at less than 50% duty cycle

I was tuning a boosted k24 with Injector clinic 2000cc injectors. I maxed out the fuel numbers really early in the tune so I turned up the overall fuel trim to 100% and started over. I successfully tuned the car to 24 psi. The duty cycle was around 47% and the # in that cell was almost 20000 (max) H...
by wiggum80
Fri Aug 10, 2012 8:45 pm
Forum: s300 / SManager
Topic: s300 has trouble uploading
Replies: 2
Views: 846

Re: s300 has trouble uploading

Fantastic service, S300 is in the car running. Thank you very much!
by wiggum80
Mon Jul 23, 2012 4:08 pm
Forum: s300 / SManager
Topic: s300 has trouble uploading
Replies: 2
Views: 846

s300 has trouble uploading

s300 ser# 12898 with software 2.1.1.0. I'm testing with the moates bseries engine simulator. When you start a new file and upload it uploads fine, it also datalogs fine. One catch, fuel pump LED isn't on. After you turn it off it won't datalog any longer and stays in limp mode. I put another s300 un...
by wiggum80
Thu May 17, 2012 11:50 am
Forum: FlashPro Manager
Topic: R18 civic w/small turbo kit goes mega rich under boost
Replies: 5
Views: 2733

Re: R18 civic w/small turbo kit goes mega rich under boost

Hmm.. well I cleared the codes and drove the car for 2 days back and forth from work. I didn't go into boost and the mil light didn't come on at all. As soon as it sees boost I get MAF malfunction code and system too rich code. Any suggestions as to what step I should take next? Any direction is muc...
by wiggum80
Tue May 15, 2012 11:36 am
Forum: FlashPro Manager
Topic: R18 civic w/small turbo kit goes mega rich under boost
Replies: 5
Views: 2733

Re: R18 civic w/small turbo kit goes mega rich under boost

serial # fp-r18-us-50163 flashpro manager version 1.2.8.0 calibration civic r18 rna 7 tsi 2009 civic dx 2dr r18 stock ecu - not original from vehicle 37820-rna-a09 modifications t28 journal bearing turbo 2.5'' exhaust with 4'' tip turbo back no cat just resonator injectors 410cc rdx motor mounts (bo...
by wiggum80
Fri May 04, 2012 11:38 am
Forum: FlashPro Manager
Topic: R18 civic w/small turbo kit goes mega rich under boost
Replies: 5
Views: 2733

R18 civic w/small turbo kit goes mega rich under boost

2009 Civic with R18 turbocharged. All is well until boost, when it crosses over from the last vacuum column it goes 10.0AFR no matter how much fuel I remove. Any ideas or suggestions will be much appreciated.
by wiggum80
Thu Mar 01, 2012 12:19 pm
Forum: K-Pro / KManager
Topic: Kpro3 upgrade
Replies: 1
Views: 749

Kpro3 upgrade

I wanted to upgrade my kpro to a kpro3. Is there a form to fill out just like the s300 upgrade? I didn't see anything listed on the website.