Is there anything in the software that can control nitrous?
The ethanol content input works off 5v, can that possibly be used?
Search found 20 matches
- Mon Jul 30, 2018 12:13 pm
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: Nitrous Control
- Replies: 1
- Views: 2207
- Mon Jul 04, 2016 9:25 am
- Forum: Civic Si 2006-2011 Americas
- Topic: Overrun throttle opening enabled checkbox not present
- Replies: 1
- Views: 1598
Overrun throttle opening enabled checkbox not present
The 06-11 Civic Si has some basemaps with a checkbox for "Overrun throttle opening enabled" and some without. I prefer to use Map based calibrations to start from because a lot of cold air intakes have the MAF sensor before the breather tube to the valvecover. Using a MAF based basemap wou...
- Mon Dec 21, 2015 12:01 pm
- Forum: TSX 2004-2014
- Topic: Looking for an output source
- Replies: 1
- Views: 4775
Looking for an output source
Working on a k series Honda Fit that uses the 07-08 TSX ecu with a Flashpro. The Car has a surge tank with 2 fuel pumps. I want to use 1 pump on the regular fuel pump circuit and the other to kick in when boost comes on. Reason being is the fuel temp gets too high idling with 2 pumps on. I've done t...
- Wed Nov 26, 2014 10:06 am
- Forum: s300 / SManager
- Topic: Datalogging extra sensors
- Replies: 2
- Views: 2187
Datalogging extra sensors
I was looking at purchasing a few extra sensors for a car I'm working on and was wondering the best way to go about setting them up to datalog in the S300. -Fuel pressure and Oil pressure (both will use AEM 0-150 psi pressure sensors) -Rear wheel speed (will use the xenocron rear wheel speed sensor ...
- Thu Oct 30, 2014 7:13 am
- Forum: s300 / SManager
- Topic: AEM wideband input
- Replies: 2
- Views: 2089
AEM wideband input
Which input pin works the best when datalogging the AEM wideband gauge? I've been using D14 ( stock 02 input) on many cars I tune but have heard the ELD pin may work better. Anyone have any thoughts or reasons one may work better than the other?
- Thu Oct 30, 2014 7:10 am
- Forum: s300 / SManager
- Topic: S300 repairable?
- Replies: 2
- Views: 1756
Re: S300 repairable?
Email sent, thank you.
- Wed Oct 29, 2014 6:22 am
- Forum: s300 / SManager
- Topic: S300 repairable?
- Replies: 2
- Views: 1756
S300 repairable?
Car was recently pulled from storage, fuel pump won't prime and solid CEL. A different ECU/s300 and the car runs perfect. Faulty Hondata s300 ser# 12194. ECU tests ok on a moates Engine simulator, ECU is a 37820-P06-A01. When uploading the s300 on the moates engine simulator you can upload and datal...
- Wed May 07, 2014 1:06 pm
- Forum: s300 / SManager
- Topic: Latest S300 (silver board) Compatibility
- Replies: 1
- Views: 1090
Latest S300 (silver board) Compatibility
I have an ecu with a first generation S300 (green board), if I purchase a new S300 (silver board) will I have to make any changes or will it drop right in without any modification?
- Tue Aug 14, 2012 11:12 am
- Forum: K-Pro / KManager
- Topic: Fuel table #s max out at less than 50% duty cycle
- Replies: 1
- Views: 1396
Fuel table #s max out at less than 50% duty cycle
I was tuning a boosted k24 with Injector clinic 2000cc injectors. I maxed out the fuel numbers really early in the tune so I turned up the overall fuel trim to 100% and started over. I successfully tuned the car to 24 psi. The duty cycle was around 47% and the # in that cell was almost 20000 (max) H...
- Fri Aug 10, 2012 8:45 pm
- Forum: s300 / SManager
- Topic: s300 has trouble uploading
- Replies: 2
- Views: 1270
Re: s300 has trouble uploading
Fantastic service, S300 is in the car running. Thank you very much!
- Mon Jul 23, 2012 4:08 pm
- Forum: s300 / SManager
- Topic: s300 has trouble uploading
- Replies: 2
- Views: 1270
s300 has trouble uploading
s300 ser# 12898 with software 2.1.1.0. I'm testing with the moates bseries engine simulator. When you start a new file and upload it uploads fine, it also datalogs fine. One catch, fuel pump LED isn't on. After you turn it off it won't datalog any longer and stays in limp mode. I put another s300 un...
- Thu May 17, 2012 11:50 am
- Forum: FlashPro Manager
- Topic: R18 civic w/small turbo kit goes mega rich under boost
- Replies: 5
- Views: 3635
Re: R18 civic w/small turbo kit goes mega rich under boost
Hmm.. well I cleared the codes and drove the car for 2 days back and forth from work. I didn't go into boost and the mil light didn't come on at all. As soon as it sees boost I get MAF malfunction code and system too rich code. Any suggestions as to what step I should take next? Any direction is muc...
- Tue May 15, 2012 11:36 am
- Forum: FlashPro Manager
- Topic: R18 civic w/small turbo kit goes mega rich under boost
- Replies: 5
- Views: 3635
Re: R18 civic w/small turbo kit goes mega rich under boost
serial # fp-r18-us-50163 flashpro manager version 1.2.8.0 calibration civic r18 rna 7 tsi 2009 civic dx 2dr r18 stock ecu - not original from vehicle 37820-rna-a09 modifications t28 journal bearing turbo 2.5'' exhaust with 4'' tip turbo back no cat just resonator injectors 410cc rdx motor mounts (bo...
- Fri May 04, 2012 11:38 am
- Forum: FlashPro Manager
- Topic: R18 civic w/small turbo kit goes mega rich under boost
- Replies: 5
- Views: 3635
R18 civic w/small turbo kit goes mega rich under boost
2009 Civic with R18 turbocharged. All is well until boost, when it crosses over from the last vacuum column it goes 10.0AFR no matter how much fuel I remove. Any ideas or suggestions will be much appreciated.
- Thu Mar 01, 2012 12:19 pm
- Forum: K-Pro / KManager
- Topic: Kpro3 upgrade
- Replies: 1
- Views: 1096
Kpro3 upgrade
I wanted to upgrade my kpro to a kpro3. Is there a form to fill out just like the s300 upgrade? I didn't see anything listed on the website.