Search found 11 matches
- Fri Sep 23, 2011 1:00 am
- Forum: s300 / SManager
- Topic: A/F wont read richier than 11.85
- Replies: 8
- Views: 3622
Re: A/F wont read richier than 11.85
I've tuned a bunch of all motor cars on s300 and they all worked fine with d10. Recently i tuned a few cars on s300 and d10 sending the votage imput from the wideband and it does not reed lower than 118.12.0. Would like to know why as well? DO i need to remove some type of resistor? Everything else ...
- Sat Apr 16, 2011 12:10 am
- Forum: S300 Calibrations
- Topic: B20B Vtec Calibration Needed Help Please!!!
- Replies: 22
- Views: 28038
- Sat Aug 21, 2010 1:28 pm
- Forum: s300 / SManager
- Topic: pressure vs duty % wont let me change back
- Replies: 5
- Views: 2403
- Fri Aug 20, 2010 2:18 pm
- Forum: s300 / SManager
- Topic: pressure vs duty % wont let me change back
- Replies: 5
- Views: 2403
You must edit it form right to left and make sure that values are not lower than the value to the left. thank you sir.. Now i got another problem, no mater what i do i can't get my a/f guage in the s300 read in a/f ratios instead of lambda. i changed the units to read in air fuel ratios and i chang...
- Wed Aug 18, 2010 1:01 am
- Forum: s300 / SManager
- Topic: pressure vs duty % wont let me change back
- Replies: 5
- Views: 2403
pressure vs duty % wont let me change back
Well before the car was tuned i changed the values to in the pressure vs duty cycle in the boost control section thinking that it would not boost anthing for some reason.haha. well now im trying to reset the values in pressure back to normal or change them to higher values but it wont let me change ...
- Tue Jul 13, 2010 12:54 am
- Forum: s300 / SManager
- Topic: Hot Temps causing Car to run Super Rich 10:1 past -10psi
- Replies: 11
- Views: 6475
Got a different basemap, seems to be running better but I am really starting to think that Locash pointed something out to me that I failed to recognize. Since I was using the WB02 for closed up via the ELD input, I probably messed up the ELD's purpose and that could explain why my problems could b...
- Tue Jul 13, 2010 12:44 am
- Forum: s300 / SManager
- Topic: D16z6, 14.8psi, 250whp 277hp.video! What do you guys think?
- Replies: 14
- Views: 7227
Very good work my friend. Nice numbers! Thanks a lot bro! I deeply appreciate your compliment! Thanks a bunch! nice work man, also don't worry too much about the a/f ratios being to lean or too rich as a safety net. Each engine will operate differently and each engine will like different a/f ratios...
- Tue Apr 27, 2010 3:50 pm
- Forum: s300 / SManager
- Topic: s300: Idle in colum 3 and 4
- Replies: 4
- Views: 3019
thank you sir for the clarification and fast response. Now i just got two more questions. what should the timing degrees be on my set up at idle should be 16degrees but what should it be throw the rpms. also to add or subtract fuel do i just go to the low speed fuel table and rev throw the rpms and ...
- Tue Apr 27, 2010 12:47 am
- Forum: s300 / SManager
- Topic: s300: Idle in colum 3 and 4
- Replies: 4
- Views: 3019
- Mon Apr 26, 2010 8:07 pm
- Forum: s300 / SManager
- Topic: s300: Idle in colum 3 and 4
- Replies: 4
- Views: 3019
also how do i adjust the fuel and everything else to keep the idle at 14.7 a/f. After 10 different all motor builds, I decided to do a turbo build and its a pain haha. lets say at idle i have 15.9 a/f on the wideband, how do i richen that up. do i just click colum 1 and 2 and add a certain amount of...
- Mon Apr 26, 2010 8:03 pm
- Forum: s300 / SManager
- Topic: s300: Idle in colum 3 and 4
- Replies: 4
- Views: 3019
s300: Idle in colum 3 and 4
Hey i just turned my car on after 400 miles of na driving. after i hooked up the turbo kit and all the components, i turned the car on and plugged in the s300 to my laptop using smanager 1.4.5 vers. My idle when data logging is at 1,100 even when its cold start and before it was at almost 2 and woul...