Search found 310 matches

by typer86
Fri Sep 22, 2017 2:58 pm
Forum: Civic Type R 2007-2011 European FN2
Topic: K20 frank 1250 to 2500 rpm throttle 0 to 100 engine is very jerky
Replies: 2
Views: 1609

Re: K20 frank 1250 to 2500 rpm throttle 0 to 100 engine is very jerky

We have fixed it. Thanks for the tipps and directions to looking for.
it was the combination of VTC and ign profile which must be adjusted to working fine.
Fuelling will be adjusted now and the calibration is finished.

engine is running fine now :-) Successfully tuned.

BR
by typer86
Wed Sep 20, 2017 8:45 am
Forum: Civic Type R 2007-2011 European FN2
Topic: K20 frank 1250 to 2500 rpm throttle 0 to 100 engine is very jerky
Replies: 2
Views: 1609

K20 frank 1250 to 2500 rpm throttle 0 to 100 engine is very jerky

Hi Hondata I am currently tune a K20 frank with K24 block with 12.5:1 high compression piston. The custom engine is working fine on the FN2 but in the rpm range: 1250 to 2500 if the throttle plate is full pressed from 0 to 100% (WOT) the engine is jerky until 2750 rpm is reached. If the pedal is rel...
by typer86
Fri Aug 25, 2017 9:37 pm
Forum: FlashPro Manager
Topic: Ignition / knock control
Replies: 9
Views: 1759

Re: Ignition / knock control

If you set 60+ on all tables, the knock logic is disabled. So k.control will not be adjusted. You can ignore it at this point. In this setup you can tune perfectly the max ign advance before knock. - check fuel (AF.corr) - check knocks - check dyno-chart for max power If you are done with ign tuning...
by typer86
Thu Aug 24, 2017 8:26 pm
Forum: FlashPro Calibrations
Topic: Race Map Calibration to Normal FN2
Replies: 4
Views: 995

Re: Race Map Calibration to Normal FN2

I can port it if you like
by typer86
Thu Aug 24, 2017 8:25 pm
Forum: FlashPro Calibrations
Topic: need k24a2 basemap for my 2010 si. will pay
Replies: 10
Views: 2573

Re: need k24a2 basemap for my 2010 si. will pay

I can create one. But no reply yet...
by typer86
Thu Aug 24, 2017 8:29 am
Forum: Civic Type R 2007-2011 European FN2
Topic: Temperature problem and engine goes very rich!
Replies: 17
Views: 5164

Re: Temperature problem and engine goes very rich!

We must retune it again. Caused by wrong injector duration in the previous firmware...
by typer86
Wed Aug 23, 2017 3:14 am
Forum: FlashPro Calibrations
Topic: Convert tables Fuel MAP a AFM
Replies: 6
Views: 1524

Re: Convert tables Fuel MAP a AFM

Spunkster wrote:
Fri Aug 18, 2017 9:29 am
You can disable it, there really is no need to completely remove it. IT contains the AIT sensor so if you do remove it, you must wire in a proper IAT sensor as well.
Yes IAT relocation is recommended...
by typer86
Wed Aug 23, 2017 2:55 am
Forum: FlashPro Calibrations
Topic: Race Map Calibration to Normal FN2
Replies: 4
Views: 995

Re: Race Map Calibration to Normal FN2

PM sent to you
by typer86
Tue Aug 22, 2017 6:57 am
Forum: Civic Type R 2007-2011 European FN2
Topic: K20/k24 frankenstein - vtc 50 degrees?
Replies: 2
Views: 1520

Re: K20/k24 frankenstein - vtc 50 degrees?

Hmm,
I hope someone had the answer :D

anyway thanks for answering.
by typer86
Tue Aug 22, 2017 6:54 am
Forum: FlashPro Manager
Topic: Ignition / knock control
Replies: 9
Views: 1759

Re: Ignition / knock control

Hmm... Interesting question.

I am not sure :D
But N/A idle's on table 2+3?
I guess col 1 is for shifting only?
by typer86
Tue Aug 22, 2017 2:21 am
Forum: FlashPro Manager
Topic: Ignition / knock control
Replies: 9
Views: 1759

Re: Ignition / knock control

Negative values will Retard Positive values will advance the ign Note: If K.Control is 0% the ECU will not Retard or advance ign. I recommend to tune the K20 with disabled knock logic. (Set knock ign Limit low and high = 60) Additional I can say for S/C and Turbo build the following works very good:...
by typer86
Mon Aug 21, 2017 12:16 pm
Forum: Civic Type R 2007-2011 European FN2
Topic: K20/k24 frankenstein - vtc 50 degrees?
Replies: 2
Views: 1520

K20/k24 frankenstein - vtc 50 degrees?

Hi Hondata,

It is possible to use for the k20 head with k24a3 block a maximum vtc of 50 degrees?
by typer86
Mon Aug 21, 2017 3:18 am
Forum: FlashPro Manager
Topic: FlashProManager 2.8.2.0
Replies: 21
Views: 4131

Re: FlashProManager 2.8.2.0

I can say AFT for the FN2 it does not work. #1 I have uploaded the calibration directly from my Notebook over the Flashpro to the ECU. (Livetuning is green - all green) #1.2 STORED calibration again on HDD. #2 Disconnect Notebook from FP #3 Start engine #4 Start datalogging and drive around After fi...
by typer86
Fri Aug 18, 2017 10:03 am
Forum: FlashPro Manager
Topic: FlashProManager 2.8.2.0
Replies: 21
Views: 4131

Re: FlashProManager 2.8.2.0

Well, I think we have identified the area which needs more work. Looking at your descriptions, and the video, you must save the calibration after uploading. Not before uploading, not while uploading, but after uploading. If the live tuning indicator is yellow it is not going to work. So I have no c...