Search found 71 matches

by 9queSt
Tue Sep 03, 2013 6:18 pm
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 34912

Re: SManager V2.2.7 (beta)

Fuel protection does not work. The afr was leaner then 11.4 in 3rd gear and the boost was well above 19psi. options....settings....units....air fuel is selected. Do I need to change it to lambda for fuel protection to work? The log shows that Im in 4th gear when its really 3rd. I think this is beca...
by 9queSt
Mon Sep 02, 2013 4:51 pm
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 34912

Re: SManager V2.2.7 (beta)

Fuel protection does not work. The afr was leaner then 11.4 in 3rd gear and the boost was well above 19psi. options....settings....units....air fuel is selected. Do I need to change it to lambda for fuel protection to work? The log shows that Im in 4th gear when its really 3rd. I think this is becau...
by 9queSt
Sun Sep 01, 2013 9:06 am
Forum: s300 / SManager
Topic: Low 10 second datalog
Replies: 10
Views: 2561

Re: Low 10 second datalog

sorry its been a while. I found out I need to make some susspension adjustments. A few months ago I set the front sturts so the front end could only lift 1 inch before the struts limited the lift. I noticed that the car now lifts to one inch and goes down the track with no susspension travel. It is...
by 9queSt
Fri Aug 30, 2013 3:42 pm
Forum: s300 / SManager
Topic: fuel pressure decreased two datalogs
Replies: 4
Views: 1328

Re: fuel pressure decreased two datalogs

It leaned up everywhere. Glad you got the launch to 10psi. If you tuned @70psi make sure you always run the car @70psi. Keep an eye on fuel pressure you may have a regulator or fuel pump quitting on you if you have to keep raising the pressure to hit 70psi. I will keep an eye on it. thank you I mad...
by 9queSt
Wed Aug 28, 2013 5:02 am
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 34912

Re: SManager V2.2.7 (beta)

perameters.....rev limit.....activation rpm and power reduction.

What was this set at in the older version that didnt allow user adjustment??
by 9queSt
Wed Aug 28, 2013 5:00 am
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 34912

Re: SManager V2.2.7 (beta)

Spunkster wrote:change your units in the sensor list to KPA and you will see it then traces correctly
It works. I like viewing the datalog in psi. if i leave it on psi with the clossed loop still work?
by 9queSt
Mon Aug 26, 2013 9:03 pm
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 34912

Re: SManager V2.2.7 (beta)

closed loop advanced.... target lambada (load).....

its stuck at 0 load. as of now the datalog is highlighting 30psi the load is stuck at 0.
by 9queSt
Mon Aug 26, 2013 1:51 pm
Forum: s300 / SManager
Topic: fuel pressure decreased two datalogs
Replies: 4
Views: 1328

Re: fuel pressure decreased two datalogs

It leaned up everywhere. Glad you got the launch to 10psi. If you tuned @70psi make sure you always run the car @70psi. Keep an eye on fuel pressure you may have a regulator or fuel pump quitting on you if you have to keep raising the pressure to hit 70psi. I will keep an eye on it. thank you I mad...
by 9queSt
Sun Aug 25, 2013 8:30 pm
Forum: s300 / SManager
Topic: Low 10 second datalog
Replies: 10
Views: 2561

Re: Low 10 second datalog

sorry its been a while. I found out I need to make some susspension adjustments. A few months ago I set the front sturts so the front end could only lift 1 inch before the struts limited the lift. I noticed that the car now lifts to one inch and goes down the track with no susspension travel. It is ...
by 9queSt
Sun Aug 25, 2013 8:23 pm
Forum: s300 / SManager
Topic: fuel pressure decreased two datalogs
Replies: 4
Views: 1328

fuel pressure decreased two datalogs

One datalog is from may and the other is from a week ago. Back in may my fuel pressure gauge was reading 70psi at idle. It now reads 60psi. Before I go and crank up the regulator Im looking for opinions. Looks like the afr did in deed lean up a bit.

What do you think??
by 9queSt
Tue Jul 30, 2013 7:58 pm
Forum: s300 / SManager
Topic: Low 10 second datalog
Replies: 10
Views: 2561

Re: Low 10 second datalog

Nice setup. While I cannot provide input on the launch & anti-lag, I can point out a couple observations. 1.) On the 1320 datalog, I noticed AFR's going full rich from timestamp 1:25 to 1:27. After looking at the fuel high cam table, It *appears* as if the tuner stopped after column 18 (27.6psi) an...
by 9queSt
Wed Jul 24, 2013 7:51 pm
Forum: s300 / SManager
Topic: Low 10 second datalog
Replies: 10
Views: 2561

Low 10 second datalog

any advice with the launch rpm/ant-lag?? what is the rpm/mph jump at 7500rpm in 3 and 4 gear?? Vehicle Make / Model / Year: 95 HONDA CIVIC Engine Model: b18c1 Setup Details (Compression/Boltons etc): Goal: 600hp @ ~25psi · E85 fuel · Precision 6262 .82ar turbine · 74mm skunk2 tb · Victor x intake ma...
by 9queSt
Thu Jul 18, 2013 3:32 pm
Forum: s300 / SManager
Topic: Boost control quit
Replies: 2
Views: 914

Re: Boost control quit

I was using version 2.2.4 when it quit working.

I just downloaded version 2.2.7 and clicked on the test function for pwm.

It stared clicking immediately. sounds like its fixed.
by 9queSt
Thu Jul 18, 2013 8:13 am
Forum: s300 / SManager
Topic: Boost control quit
Replies: 2
Views: 914

Boost control quit

The boost control quit working on me at the track last night. Hondata/Mac solenoid. I tested the pwm output, the solenoid didn't make a sound The solenoid has power. The solenoid clicks when 12v and ground is applied to it. The wire from A11 to the solenoid is good. It must be something inside the e...
by 9queSt
Mon Jul 08, 2013 7:17 pm
Forum: s300 / SManager
Topic: cpr compression test
Replies: 1
Views: 775

cpr compression test

Im doing a compression test on my civic that has CPR.

I can unplug the dizzy plug, the cpr box plug and each coil.

Should I unplug all or just one??