Search found 71 matches

by 9queSt
Fri Mar 15, 2013 10:05 am
Forum: s300 / SManager
Topic: digital/ analog wodeband input
Replies: 3
Views: 1070

Re: digital/ analog wodeband input

You cannot use autotune with the inputs on the s300 board. They are for datalogging only. For autotune to work you must input the wideband signal into one of hte ECU inputs listed in the software. the wideband analog signal is inputted to b6 with r2 and r3 cut. I selected b6 to run closed loop. Is ...
by 9queSt
Fri Mar 15, 2013 5:17 am
Forum: s300 / SManager
Topic: digital/ analog wodeband input
Replies: 3
Views: 1070

digital/ analog wodeband input

Under the settings, sensor overlay tab i selected digital 0. This is what my wideband is connected to.
The analog portion of my wideband is connected to b6 (analog 2). R2 &R3 cut. Does autotune use digital 0 or analog 2?

Thanks
by 9queSt
Sat Mar 02, 2013 7:56 pm
Forum: s300 / SManager
Topic: E85 max torque or detonation
Replies: 1
Views: 877

E85 max torque or detonation

When tuning with e85 @ 30psi and about 625hp.

Tuning on a dyno, as timing is slowly increased, does max torque occur before of after detonation?
by 9queSt
Wed Feb 27, 2013 9:22 pm
Forum: s300 / SManager
Topic: CPR Disable Alternator control
Replies: 5
Views: 1797

Re: CPR Disable Alternator control

V-Spec race development wrote:
9queSt wrote:In Smanager>misc> disable alternator control

Should this be selected when using CPR?
The car may not start if you have this check. I had this happened on my buddy's car. Unchecked it and start right up.
Did your friend have cpr ??
by 9queSt
Sat Feb 23, 2013 8:35 pm
Forum: s300 / SManager
Topic: CPR Disable Alternator control
Replies: 5
Views: 1797

CPR Disable Alternator control

In Smanager>misc> disable alternator control

Should this be selected when using CPR?
by 9queSt
Sat Feb 23, 2013 7:09 pm
Forum: s300 / SManager
Topic: CPR Yellow Wire
Replies: 1
Views: 764

CPR Yellow Wire

Harness variation B.
black= ground
red= +12v
Yellow/red= ICM A22
purple= SYNC A16
green= Tach output

Yellow= ign1, is that the wire that powers the factory coil?
by 9queSt
Wed Feb 13, 2013 5:09 pm
Forum: s300 / SManager
Topic: closed loop b6
Replies: 1
Views: 644

closed loop b6

plx-smafr
p72

I have the analog output from the plx connected to b6.

Do I need to cut any resistors for b6 to work?
by 9queSt
Wed Feb 06, 2013 7:40 pm
Forum: s300 / SManager
Topic: Closed loop advanced
Replies: 1
Views: 764

Closed loop advanced

Under closed loop advance. Setting target lambada with MBAR and lambada.

Is the MBar scale absolute or atmospheric?
by 9queSt
Tue Feb 05, 2013 8:26 pm
Forum: s300 / SManager
Topic: Full throttlle shift
Replies: 16
Views: 6820

Re: Full throttlle shift

Spunkster wrote:Full throttle shift will be set at a higher RPM than the launch control will be and launch control will only work below a set speed.
My next gears rpm, 3rd to 4th, is about 6000rpm. should i set fts at 6000?

My launch control is at 6500.
by 9queSt
Sat Feb 02, 2013 10:12 am
Forum: s300 / SManager
Topic: Full throttlle shift
Replies: 16
Views: 6820

Re: Full throttlle shift

Spunkster wrote:Launch control only works below a certain speed.
when launch control is activated under (certain speed) and fts is activated because the clutch switch activating it is pushed in. Does launch control get the priority?
by 9queSt
Tue Jan 29, 2013 6:58 pm
Forum: s300 / SManager
Topic: Full throttlle shift
Replies: 16
Views: 6820

Re: Full throttlle shift

Fts has to be activated by a switch that is triggered as soon as you push the clutch in. Its basically a rev limit that is activated when the clutch is pressed.

When FTS is grounded it should be activated.

Spunkster, does launch control override fts?
by 9queSt
Sat Jan 12, 2013 12:00 pm
Forum: s300 / SManager
Topic: Full throttlle shift
Replies: 16
Views: 6820

Full throttlle shift

Under full throttle shift parameters in the s300 user guide.... it says the activation, input- selects the arming input for the launch control.. does this mean the arming input for full throttle shift? ------ Full throttle, activates with clutch switch when clutch peddle is pressed. set to 6000rpm L...
by 9queSt
Wed Jan 09, 2013 8:40 am
Forum: s300 / SManager
Topic: boost control with nitrous/aux1
Replies: 7
Views: 1656

Re: boost control with nitrous/aux1

Spunkster wrote:Sorry, I misunderstood your question originally.

The outputs above are ground triggers and will ground as long as the other side is connected to a power source.

The above post has been edited.
Thanks. I can see how it can easily be misunderstood. Thanks for verifying.
by 9queSt
Tue Jan 08, 2013 9:22 pm
Forum: s300 / SManager
Topic: launch soft
Replies: 3
Views: 1495

launch soft

what does Launch soft do?

Will it increase EGT or have any harmful effects?
by 9queSt
Tue Jan 08, 2013 8:58 pm
Forum: s300 / SManager
Topic: Rev limit Ign and fuel cut
Replies: 1
Views: 884

Rev limit Ign and fuel cut

With a stock ignition can I use fuel and Ignition cut?

what are the benefits of one vs the other?

selecting ignition cut disables the ecu igniter output, will this essentially allow the engine to over rev? since its not getting a tach reading.