Search found 71 matches

by 9queSt
Tue Jan 08, 2013 5:09 pm
Forum: s300 / SManager
Topic: e85 turbo and detination opinions of timing map please
Replies: 5
Views: 2400

Re: e85 turbo and detination opinions of timing map please

it looks like he set up secondary tables. these are enabled when you push the ac switch. You timing looks good. about 17 degrees in column 14 and 32 degrees in column 10.

Did he tell you to push ac switch at any point?
by 9queSt
Tue Jan 08, 2013 4:31 pm
Forum: s300 / SManager
Topic: launch control tach crazy
Replies: 10
Views: 2202

Re: launch control tach crazy

justagsr wrote:right. should i not have fuel and ignition cut?
if you just use fuel cut your tach wont go screwy.
by 9queSt
Tue Jan 08, 2013 4:09 pm
Forum: s300 / SManager
Topic: boost control with nitrous/aux1
Replies: 7
Views: 1655

Re: boost control with nitrous/aux1

You would have to use one of the outputs that is a ground. All the outputs you have mention are powered and not ground triggered and you may damage the ECU if you wire it incorrectly. In the hondata s300 programmable ecu guide, windows, parameters window, nitrous parameters scroll to the bottom. th...
by 9queSt
Tue Jan 08, 2013 12:46 pm
Forum: s300 / SManager
Topic: boost control with nitrous/aux1
Replies: 7
Views: 1655

Re: boost control with nitrous/aux1

thank you.
by 9queSt
Mon Jan 07, 2013 6:32 pm
Forum: s300 / SManager
Topic: boost control high to low in 3rd
Replies: 2
Views: 850

Re: boost control high to low in 3rd

Spunkster wrote:You cannot expect it to drop 10psi in a few hundred RPM once it is already spooled up.

Thanks for the quick reply. I was just thinking that this morning. Just never tested it.
by 9queSt
Mon Jan 07, 2013 6:31 pm
Forum: s300 / SManager
Topic: boost control with nitrous/aux1
Replies: 7
Views: 1655

Re: boost control with nitrous/aux1

You would have to use one of the outputs that is a ground. All the outputs you have mention are powered and not ground triggered and you may damage the ECU if you wire it incorrectly. If I ground the controller, and send 12v to it with A15, A17, A20 to switch it, will that be a problem? are a12 a16...
by 9queSt
Mon Jan 07, 2013 5:54 am
Forum: s300 / SManager
Topic: boost control high to low in 3rd
Replies: 2
Views: 850

boost control high to low in 3rd

Is it okay to switch from high to low boost at the top of 3rd gear?

In third, boost will switch from 25psi to 15psi at about 8400rpm.
normally ill shift at 8200 rpm. If i mistakenly shifted at 8600, would it be dangerous?
by 9queSt
Sun Jan 06, 2013 11:56 am
Forum: s300 / SManager
Topic: boost control with nitrous/aux1
Replies: 7
Views: 1655

boost control with nitrous/aux1

Dual stage turbo xs boost controller. As of now I have a switch to ground the controller. When the controller is grounded it switches to high boost. I want to enable high boost with nitrous/aux1 parameters. What output should I use under nitrous control to enable the high boost? Will I fry the ecu i...
by 9queSt
Sat Jan 05, 2013 8:52 pm
Forum: s300 / SManager
Topic: target lambada, ignition timing e85, boost tables. FAST!!!
Replies: 0
Views: 1161

target lambada, ignition timing e85, boost tables. FAST!!!

gsr 84mm
s300v2
stock head
rods and pistons 9:1
pte6262
e85

Im looking to make about 600whp @ about 25psi.

What is a good target lambada or afr? 7.6afr= .78lambada?
how does my ignition look?
How much fuel should I add in the boost tables to start with? I have read anywhere between 130 to 175%
by 9queSt
Fri Jan 04, 2013 11:56 am
Forum: s300 / SManager
Topic: GM 3 bar MAP sensor
Replies: 15
Views: 11530

Re:

so the GM 3bar MAP sensor has a scaler of 628 and an offset of 0, and the Motec 3bar MAP sensor has a scaler of 609 and an offset of 2, so am i correct that I need to switch my scaler and offset to the GM settings??? can I get some help here Hondata??? This would be much easier if you just included...