Search found 100 matches

by Zperformance
Thu Apr 13, 2017 7:00 pm
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

Datalog(display menu) with your laptop plugged and look at your ect sensor. It will tell you the actual heat of the coolant. Have you bleed the coolant system? Check your vaacum hoses see if there is any leaks.
by Zperformance
Thu Apr 13, 2017 6:14 pm
Forum: K-Pro Calibrations
Topic: K24a3 map needed
Replies: 2
Views: 822

Re: K24a3 map needed

Run the tsx basemap?
by Zperformance
Thu Apr 13, 2017 8:23 am
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

Okay. Thats awesome! Since it could idle and start no problem. No rush just lmk if you need anything.

And yeah my paypal is just zoua95@yahoo.com
by Zperformance
Thu Apr 13, 2017 1:49 am
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

You dont have too, i just hope it worked for you and give me feedback haha for more experience.

I never had someone paypal me so Is it just my email for paypal? If it is then its just zoua95@yahoo.com

Is it a nice stable idle? Lmk how DD and full throttle is.
by Zperformance
Mon Apr 10, 2017 9:36 pm
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

I lower Vtec to 4000RPM since the you are bolt on and lower your Rev limit to 8500. I recommend you to have a wideband and adjust your full throttle to spec. If you have your o2 sensor on it will compensate and fix the lean or rich mixture during Daily portion. I dial in your injector it should be b...
by Zperformance
Sun Apr 09, 2017 5:30 pm
Forum: FlashPro Calibrations
Topic: Drop in power on each dyno run
Replies: 3
Views: 1632

Re: Drop in power on each dyno run

Compression test. Add more fuel into cylinder 2 and see.
by Zperformance
Sun Apr 09, 2017 5:27 pm
Forum: FlashPro Calibrations
Topic: dies after idle...
Replies: 4
Views: 1254

Re: dies after idle...

^like he says, deadtime matters!
by Zperformance
Sun Apr 09, 2017 5:24 pm
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

Go to online-> tools-> download

Do this with the car on accessory or with the car running.
by Zperformance
Sun Apr 09, 2017 12:36 pm
Forum: K-Pro Calibrations
Topic: Tuning a JRSC K24a2 RSX
Replies: 8
Views: 2017

Re: Tuning a JRSC K24a2 RSX

Are you tuning with an actual aftermarket wideband? Or just the oem wb02?

What oil areyou running? Alot of Force induction car i tuned, they switch over to thicker oil and the engine and engine bay runs cooler also.
by Zperformance
Sun Apr 09, 2017 10:50 am
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

Upload your current tunr that you are using to start up the car.
by Zperformance
Sun Apr 09, 2017 10:49 am
Forum: K-Pro Calibrations
Topic: basemap needed
Replies: 13
Views: 1704

Re: basemap needed

Did you dial in your injectors?
by Zperformance
Sat Apr 08, 2017 2:21 pm
Forum: K-Pro Calibrations
Topic: Looking for base map k24a2 turbocharged
Replies: 1
Views: 671

Re: Looking for base map k24a2 turbocharged

What brand injector
by Zperformance
Sat Apr 08, 2017 2:21 pm
Forum: K-Pro Calibrations
Topic: Kind of panicking
Replies: 4
Views: 762

Re: Kind of panicking

I would rather run the basemap off of kpro for the k20a3 they should be capable to drive DD i wouldnt smash on the car unless you have a wideband to make sure its safe. And pumping 93 to blend with the 89. You would want close to a 91 octane mix. Try to get a good full 91+ octane mix before taking i...
by Zperformance
Fri Apr 07, 2017 9:50 pm
Forum: K-Pro Calibrations
Topic: Kind of panicking
Replies: 4
Views: 762

Re: Kind of panicking

Try pumping 91 octane and octane booster to bump up the octane. Running 89 octane you will be knock limited
by Zperformance
Fri Apr 07, 2017 9:38 am
Forum: S300 Calibrations
Topic: new to Hondata! help with h22
Replies: 2
Views: 1355

Re: new to Hondata! help with h22

I advice having a wideband to adjust afr to spec. Give me feedback if there is any problem i will try to help with what i can.