Search found 72 matches

by hiperformance
Tue Sep 11, 2007 1:52 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Any idea? still cannot data log a/f below 11.82

thanks.
by hiperformance
Mon Sep 10, 2007 12:50 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Here is the data log with D10 disconnected. ELD reads 4.53v-4.55v the next is a data log from a 3rd gear dyno pull, 2 points the air fuel on the data log read 11.82, around 5100 rpm and 6100 rpm. at the same 2 points the plx and dyno both read 10.xx, the data log will not record below 11.82? your he...
by hiperformance
Fri Sep 07, 2007 10:27 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

4.5v
by hiperformance
Fri Sep 07, 2007 1:37 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

I did another data log. but I forgot to save it. I did observe the plx box reading 10.6-10.8 and the hondata log was firm at 11.86
by hiperformance
Thu Sep 06, 2007 2:32 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

ok, I changed the AF to min 10 and max 20.
by hiperformance
Thu Sep 06, 2007 2:20 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

ok, is this right? I go into sensor set up and only change the AF display min and max.

the rest I assume inj, map and rpm are all correct, sense it was pre-set.

thanks.
by hiperformance
Thu Sep 06, 2007 2:16 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Spunkster wrote:Your graphs should be set to a min of 10 and a max of 20.
I assume only the AF needs to be changed to a min of 10 and a max of 20.

thanks.
by hiperformance
Thu Sep 06, 2007 4:01 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Here is the dyno graph. That 11.66 shows 11.82 on the hondata display, but the plx screen and dyno read 11.66.
by hiperformance
Thu Sep 06, 2007 4:00 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

I did 4 datalogs, maybe I am data logging wrong? I right clicked the graph screen, graph templates box poped up. I added AF with the color clMaroon to graph 3 so I could see what the AF was doing. I data logged and got nothing for AF? I did a dyno run and the car stumbled real bad, as it was stumbli...
by hiperformance
Wed Sep 05, 2007 1:53 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Have you done anything not described in the PLX wiring instructions located on our website? Have you added any additional components (capacitors)? no additional components were added, i even printed the directions out and once i made the mistake of using the wrong pin for the input, i have gone ove...
by hiperformance
Tue Sep 04, 2007 2:57 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Try decelerating and see how lean it will go Ok, I did the test, on deceleration, in the display screen, the lambda value goes to 19.36, the plx goes to AIR. if i richen up the idle cells, lambda value in the display screen freezes at 11.82, if I keep richening it up, the plx and dyno afr's will co...
by hiperformance
Sat Sep 01, 2007 3:23 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Spunkster wrote:Try decelerating and see how lean it will go
Ok, on deceleration, in the display screen, the lambda value goes to 19.36, the plx goes to AIR.
by hiperformance
Thu Aug 30, 2007 12:43 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Spunkster wrote:What is the leanest it will read?
I leaned it out all the way to 16 reads fine to there, 16 is where I stopped. is there a test or a check I should try?
by hiperformance
Thu Aug 30, 2007 1:43 am
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

The only way I can reproduce what you describe is if i do not disconnect the ELD wire from the eld itself. Double check your wiring. Disconnect the white wire from the eld input and datalog and look at the eld voltage in the sensor list What is it doing? Great suggestion. I checked the eld sensor v...
by hiperformance
Tue Aug 28, 2007 12:37 pm
Forum: s300 / SManager
Topic: help setting up plx m-300 with s300 for closed/open loop
Replies: 40
Views: 17006

Spunkster wrote:Have you cut the wire that originally went to the ELD?
Yes, the wire is cut on the jumper harness about 2" from the ecu. the 0-5v white from the plx is attached to that wire coming from the ecu.