Search found 104 matches

by sass
Tue Jul 23, 2013 9:57 am
Forum: K-Pro / KManager
Topic: KPro / KManager requests
Replies: 121
Views: 47192

Re: KPro / KManager requests

Hondata
Is it possible to add function in datalog to close ALL log files
by sass
Tue Jul 16, 2013 8:12 am
Forum: FlashPro Manager
Topic: FlashPro V1.6.3
Replies: 103
Views: 33488

Re: FlashPro V1.6.0

What vehicles / ECUs are involved, and what FlashPros are being used? We've only just started selling the Accord FlashPro, so it seems like you may be using the TSX FlashPro. Is that the case? There are many Accord/TSX 09-10 users in Europe and Russia who use Flashpro. In 2012 this was the only way...
by sass
Tue Jul 16, 2013 2:41 am
Forum: FlashPro Manager
Topic: FlashPro V1.6.3
Replies: 103
Views: 33488

Re: FlashPro V1.6.0

Hondata 3 (three) Hondata ECUs of my clients´ Honda Accord 2010 have erro coded P0128. This error is fixed for Civic K24 2012. Is it possible to fix it for other Hondas too? Ilx 2013 Tsx 2009-2010 International Accord 2008-2010 Add: When we activate secondary water sensor the error p0128 does not a...
by sass
Mon Jul 08, 2013 11:26 pm
Forum: FlashPro Manager
Topic: FlashPro V1.5.6
Replies: 68
Views: 23599

Re: FlashPro V1.5.6

Zoro2006: This is to prevent manual transmission calibrations from being loaded into automatic transmission ECUs. BWelbourn: You need to upload to the ECU again with 1.5.6 "automatic gear, manual transmission is not the problem, because when i load my calibration in PC the error appears. There were...
by sass
Sat Jul 06, 2013 7:50 am
Forum: FlashPro Manager
Topic: FlashPro V1.5.6
Replies: 68
Views: 23599

Re: FlashPro V1.5.6

I have the same problem
by sass
Fri Mar 08, 2013 11:01 am
Forum: K-Pro / KManager
Topic: PLX devices digital input - Kpro III
Replies: 10
Views: 3890

Re: PLX devices digital input - Kpro III

jbaker Can You show your scheme of connection for digital unit? I made a male 3.5mm jack and connected signal (yellow wire) and ground (black) to the 4 pin connector on the Hondata digital input: Here you can see where I connected the 4 pin connector. I connected the black wire to ground and yellow...
by sass
Thu Mar 07, 2013 12:19 am
Forum: K-Pro / KManager
Topic: PLX devices digital input - Kpro III
Replies: 10
Views: 3890

Re: PLX devices digital input - Kpro III

jbaker
Can You show your scheme of connection for digital unit?
by sass
Sun Jan 20, 2013 11:21 pm
Forum: TSX 2004-2014
Topic: Auto gearbox 3 - 4 - 5 gear lag
Replies: 5
Views: 4843

Re: Auto gearbox 3 - 4 - 5 gear lag

My friends has same problem.

avtomat gear
Image

tiptronic gear
Image
by sass
Mon Dec 03, 2012 4:39 am
Forum: General / Traction Control Manager Software
Topic: Drag car settings
Replies: 14
Views: 10963

Re: Drag car settings

Bard
+1
by sass
Fri Nov 09, 2012 10:39 pm
Forum: Traction Control with KPro
Topic: TC on RSX Problems
Replies: 15
Views: 11922

Re: TC on RSX Problems

This is the default value for "RSX2006") Thank you! In the evening, I can check!) Hurray!!! TC is working!!! Hard to believe I did not notice that the selected rear-wheel drive. You are planning fix the default setting for "RSX 2006"? If you look "Slip setup" Cornering for RSX is very similar to S2...
by sass
Thu Oct 11, 2012 2:22 am
Forum: FlashPro Manager
Topic: Knock Control
Replies: 2
Views: 3032

Re: Knock Control

The knock tables were created using RON octane ratings, not pump octane numbers. If the ignition tables were set all below the knock threshold then the knock control should set low. In practice, this is very difficult to do on pump fuel. Knock control will change the ignition timing, but not fuel. ...
by sass
Wed Mar 14, 2012 11:30 am
Forum: FlashPro Manager
Topic: FlashProManager V1.2.7 (beta)
Replies: 59
Views: 22621

Re: FlashProManager V1.2.7 (beta)

DELETE
by sass
Wed Mar 14, 2012 1:09 am
Forum: FlashPro Manager
Topic: FlashProManager V1.2.7 (beta)
Replies: 59
Views: 22621

Re: FlashProManager V1.2.7 (beta)

V1.2.8 changes (13 March 2012)
[Civic R18] Added MAP based fuel table option
[S2000] Fixed boost cut not working.
[07-08 TSX] Fixed error under boost.
[07-08 TSX] Added EVAP error code disable.
[07-08 TSX] Added calibrations.

Hondata Thanks
by sass
Fri Feb 10, 2012 12:12 am
Forum: FlashPro Manager
Topic: FlashProManager V1.2.7 (beta)
Replies: 59
Views: 22621

Re: FlashProManager V1.2.3 (beta)

Hondata I had now set up the client car remotely.
And what I got?
Image

Thank you for a broken day