Search found 72 matches
- Thu Mar 20, 2014 1:55 am
- Forum: s300 / SManager
- Topic: how to power up P28 on bench
- Replies: 2
- Views: 1681
Re: how to power up P28 on bench
Thank you!
- Thu Mar 13, 2014 1:56 am
- Forum: s300 / SManager
- Topic: how to power up P28 on bench
- Replies: 2
- Views: 1681
how to power up P28 on bench
what pins would need power and grounds if I wanted to power up an obd1 p28 on my desk so I can register the s300 online. I have a pig tail to do this with.
thank you.
thank you.
- Thu Dec 16, 2010 4:28 pm
- Forum: s300 / SManager
- Topic: Does it make a difference which ECU you use for the S300?
- Replies: 15
- Views: 10796
- Wed Dec 15, 2010 8:39 pm
- Forum: s300 / SManager
- Topic: Does it make a difference which ECU you use for the S300?
- Replies: 15
- Views: 10796
- Wed Dec 15, 2010 2:48 pm
- Forum: s300 / SManager
- Topic: Does it make a difference which ECU you use for the S300?
- Replies: 15
- Views: 10796
- Wed Dec 15, 2010 1:18 am
- Forum: s300 / SManager
- Topic: Does it make a difference which ECU you use for the S300?
- Replies: 15
- Views: 10796
- Tue Dec 14, 2010 1:11 pm
- Forum: s300 / SManager
- Topic: Does it make a difference which ECU you use for the S300?
- Replies: 15
- Views: 10796
- Tue Dec 14, 2010 12:14 am
- Forum: s300 / SManager
- Topic: Does it make a difference which ECU you use for the S300?
- Replies: 15
- Views: 10796
Does it make a difference which ECU you use for the S300?
The question is regarding USDM ecu's and the S300.
Is there any difference between using a P72 or p28? Is there any advantage the p72 has over the p28 or any advantage the p28 has over the p72?
Thanks.
Is there any difference between using a P72 or p28? Is there any advantage the p72 has over the p28 or any advantage the p28 has over the p72?
Thanks.
- Fri Feb 26, 2010 1:56 pm
- Forum: K-Pro / KManager
- Topic: Upload Fail?
- Replies: 1
- Views: 1375
Upload Fail?
Kpro will not upload? all software is up to date, all drivers are up to date. Even tried removing it and installing it into another vehicle and still upload fail? any ideas?
- Mon Jan 18, 2010 3:12 am
- Forum: s300 / SManager
- Topic: Please check this datalog.....TPS goes wack in 4th?
- Replies: 2
- Views: 1772
The length of the data log is interesting. On that particular pass the car ran a 10.9 quarter mile. I had been mentioning to the driver that his shifts were a bit sluggish, I think he is traumatized by bad down shift mishap in the past. On the 1 to 2 shifts, you can actually see the front of the car...
- Wed Jan 13, 2010 2:46 am
- Forum: s300 / SManager
- Topic: Please check this datalog.....TPS goes wack in 4th?
- Replies: 2
- Views: 1772
Please check this datalog.....TPS goes wack in 4th?
This datalog was taken during a pass on the drag strip. The car started lunging and running bad for a little bit in 4th then it cleared and pulled strong again. From the point of shifting into 4th the gas pedal was pressed to the floor and never lifted. The datalog shows the TPS fluctuation? startin...
- Thu Nov 19, 2009 1:29 am
- Forum: s300 / SManager
- Topic: Air fuel runs away at idle?
- Replies: 4
- Views: 2566
the idle can be tuned perfect, then after a minute of idling, the air fuel runs away and it needs to be returned, changes are made to the fuel table, considerable changes, idles nice then after a minute, the air fuel runs away again. starts idling rough then dies. the wideband is not hooked in the d...
- Sat Oct 03, 2009 3:57 am
- Forum: s300 / SManager
- Topic: Air fuel runs away at idle?
- Replies: 4
- Views: 2566
Air fuel runs away at idle?
Just sitting idling smooth at 14:1, the air fuel stays for a bit, then goes to lean, with out touching anything. what would cause that?
- Thu Jan 22, 2009 2:29 am
- Forum: s300 / SManager
- Topic: HELP PLX INSTALLATION S300
- Replies: 2
- Views: 2738
I would search the help files or this forum for more in depth information. but.... Go to: parameters, Closed Loop. the wideband lambda table is at the bottom of that page. I believe the voltage/ conversion table is already preset for the PLX. 0v=10 and 5v=20. from there you choose which input source...
- Mon Jan 19, 2009 1:38 am
- Forum: s300 / SManager
- Topic: error downloading update 1.4.0.0?
- Replies: 4
- Views: 2698