Search found 64 matches
- Mon Apr 23, 2012 1:35 am
- Forum: TSX 2004-2014
- Topic: What can I expect from FlashPro for 07 TSX Daily Driver
- Replies: 5
- Views: 7513
Re: What can I expect from FlashPro for 07 TSX Daily Driver
You guys have to tune vtc precisely, stock cals dont have this. It can give you much right from 2k rpm , entirely new feeling at part throttle and city driving.
- Mon Apr 09, 2012 9:37 am
- Forum: TSX 2004-2014
- Topic: Flashpro triggers VSA error and blinking check engine symbol
- Replies: 9
- Views: 7292
Re: Flashpro triggers VSA error and blinking check engine sy
I just pulled all pins out of connector and tried to push em to flashpro plug contacts separately, few of em r holding good , few r loose This was what I was referring to when I said I was surprised it was working at all. But i returned em back to connector after checking em !! Just bent few of em ...
- Sun Apr 08, 2012 7:39 am
- Forum: TSX 2004-2014
- Topic: Flashpro triggers VSA error and blinking check engine symbol
- Replies: 9
- Views: 7292
Re: Flashpro triggers VSA error and blinking check engine sy
core, i havent cut CAN completely , i just connected to it on E connector , cut off isolation off wire and soldered to it. VSA works just fine untill i plug in flashpro to OBD . As for voltage on WEN pin - Derek , i tried to measure it when i saw WEN error , something like 3 volts for few seconds . ...
- Sun Apr 08, 2012 4:20 am
- Forum: TSX 2004-2014
- Topic: Flashpro triggers VSA error and blinking check engine symbol
- Replies: 9
- Views: 7292
Re: Flashpro triggers VSA error and blinking check engine sy
I'm surprised it works at all. The VSA uses the same CAN bus as is in the OBDII connector and if there is any problem with the wiring it is going to affect the VSA to ECU communication. My suggestion would be to put the terminals back in the OBDII connector. Im sorry, could you explain more detaile...
- Fri Apr 06, 2012 2:51 pm
- Forum: TSX 2004-2014
- Topic: Flashpro triggers VSA error and blinking check engine symbol
- Replies: 9
- Views: 7292
Re: Flashpro triggers VSA error and blinking check engine sy
My car isnt supported oficially, its EDM CL9. I often see CEL is blinking once or more while im inserting flashpro to obd connector. It may be because of bad connection. I just pulled all pins out of connector and tried to push em to flashpro plug contacts separately, few of em r holding good , few ...
- Thu Apr 05, 2012 1:56 pm
- Forum: TSX 2004-2014
- Topic: Flashpro triggers VSA error and blinking check engine symbol
- Replies: 9
- Views: 7292
Flashpro triggers VSA error and blinking check engine symbol
Today i wasnt able to flash ecu , even after 40 min of drive and 30-40 min of idle. Im tuning my car for almost 10 days , some days i have good flashing luck , some - not , but story all the same - WEN error. Checked again everything , wires , voltage , everything looks fine. Flashpro was connected ...
- Wed Apr 04, 2012 2:18 am
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
This problem get worse and worse , today i wasnt able to flash my ecu after 30 min run. I also tried to flash with charger , checked voltage on battery pins - 14.4 volts , when i turn ignition on it drops to 11.9 - 12.2 and still WEN error. Hondata , please find why it happens with tsxers and solve ...
- Mon Apr 02, 2012 4:44 am
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
Yesterday i had to flash multiple cals to make few datalogs. I run my car , then stopped to upload new cal to flashpro or ecu, again and again. I can clearly say now that its really voltage issue coz everything else was constant. Leaving car with headlights on or rear window heater on for few minute...
- Fri Mar 30, 2012 11:44 am
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
I found few of your posts bout this error and that low voltage is the problem so I fully charged my battery and connected Ctek charger on top in a power supply mode. Cant imagine more stable voltage situation in my case, I even never start engine after charging battery but nothing changed, WEN error...
- Tue Mar 27, 2012 7:46 am
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
Yep core58 , i also dont see nothing annoying here , except that fact that Hondata told us to check wiring and OBD port instead of tell us to warm up the car before flashing. I wasnt too happy to waste almost a day to find a problem, i cutted and sliced half of my native wires. Im shure that avg Joe...
- Mon Mar 26, 2012 2:30 pm
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
Anyone who have such problem or dont have are welcome to my thread . Just leave +1 or -1 .
Hondata , where r you ? This post is on your forum and its related to your product . Its not a problem to start car and wait for 5 mins , but its weird ))
Hondata , where r you ? This post is on your forum and its related to your product . Its not a problem to start car and wait for 5 mins , but its weird ))
- Mon Mar 26, 2012 9:10 am
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
Just wanted to post same link here . So i see im not alone and problem really persists.
We need to find now what is the source of the problem , cold ecu or cold flashpro box or this is SW bug.
HONDATA, i guess the time has come for your comments bout this problem .
We need to find now what is the source of the problem , cold ecu or cold flashpro box or this is SW bug.
HONDATA, i guess the time has come for your comments bout this problem .
- Mon Mar 26, 2012 8:49 am
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
Just tried to wire spare obd connector directly to E connector . Absolutely same result ! ECU or flashpro box itself must be WARM. Cold car - fail, warm car - ok . Its ABSOLUTELY non wiring problem, its software \ flashpro box \ ecu problem . Hey Zorro , and anyone who has same trouble , try to do n...
- Sun Mar 25, 2012 2:44 pm
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
Tried today , absolutely same result , WEN error utill i warm up interior for 5-10 minutes. After warming up everything smooth. My buddy also asked few FN guys bout this WEN problem , they told that with older managers , before TSX was released , everything was fine , then it starts to work weird.
- Sat Mar 24, 2012 12:47 pm
- Forum: TSX 2004-2014
- Topic: cant upload cal to ecu
- Replies: 27
- Views: 17987
Re: cant upload cal to ecu
And the FINAL update for this story. I digged really HARD in this and found a post on tsxclub where the guy had same problem as me . He uploaded just fine after he drive his car. So it was warmed. I JUST WARMED MY CAR FOR 10 MINUTES AND CAL UPLOADED WITHOUT ANY ERRORS. ALL YOU GUYS WHO HAS SAME ERRO...