Search found 45 matches

by AngryScottish
Sat Oct 02, 2021 12:50 pm
Forum: K-Pro / KManager
Topic: S2000 Kpro Low/High Boost
Replies: 20
Views: 2379

Re: S2000 Kpro Low/High Boost

I'm am looking to add a switch for low/high boost as well, using the E16 pin. What I'm finding is the E16 pin is putting out 12V. is that normal? Grounding it has Kpro show that the EPS switch is on... so I'm hoping I'm good there. However, it's doing nothing for my Boost Control. I have my low boos...
by AngryScottish
Wed Jan 13, 2021 11:29 am
Forum: K-Pro / KManager
Topic: ECU main board component - what does it do?
Replies: 4
Views: 700

Re: ECU main board component - what does it do?

Spunkster wrote: Tue Jan 12, 2021 2:47 pm I can't tell you what it will do if it is not connected properly. You will have to test and see if it works as it should.
Thanks for the response -- pointing it out as a capacitor was actually pretty helpful.

I'm going to just solder in a new one properly, and hope for the best.
by AngryScottish
Tue Jan 12, 2021 2:38 pm
Forum: K-Pro / KManager
Topic: ECU main board component - what does it do?
Replies: 4
Views: 700

Re: ECU main board component - what does it do?

Do you know if the ECU will power up if that capacitor isn't connected (or properly connected)?

Trying to determine a way to test if I soldered it enough for it to perform it's function.
by AngryScottish
Tue Jan 12, 2021 11:48 am
Forum: K-Pro / KManager
Topic: ECU main board component - what does it do?
Replies: 4
Views: 700

ECU main board component - what does it do?

While adding a connector for the digital and analog headers, I accidentally snapped off a round component on the main board with polarity symbols. I did my best to solder it back into place, but in case it didn't work, what does that component do so I know what to expect if things don't work? I've a...
by AngryScottish
Fri Sep 04, 2020 8:59 am
Forum: K-Pro / KManager
Topic: How does the VSS interact with the tune?
Replies: 1
Views: 2234

How does the VSS interact with the tune?

Just curious how the tune is adjusted based on signal from the VSS.

Does it adjust timing, fueling, spark, etc?
by AngryScottish
Thu May 23, 2019 1:38 pm
Forum: K-Pro / KManager
Topic: PS Pump Switch - E16
Replies: 2
Views: 713

Re: PS Pump Switch - E16

got it, thanks for the super quick reply!
by AngryScottish
Thu May 23, 2019 1:15 pm
Forum: K-Pro / KManager
Topic: PS Pump Switch - E16
Replies: 2
Views: 713

PS Pump Switch - E16

ECU: KPro V4 Before I go about reinventing the wheel (pun not intended), I have a Mini Cooper EHPS pump installed. It currently runs whenever the ignition is on. After fiddling with some wiring diagrams... I noticed that pin E16 is for the PS Pump switch... I'm not sure how the original system funct...
by AngryScottish
Sun Sep 09, 2018 4:14 pm
Forum: K-Pro / KManager
Topic: AIM Solo2 DL - CANBus
Replies: 1
Views: 990

AIM Solo2 DL - CANBus

I have a KPro V4 exporting CAN data to an Aim Solo2 DL. I have the Digital Output set to AIM MXL I have the CAN Output set to MoTeC SDL/ADL I have PLX sensor data being set to the digital inputs, as described here: https://www.hondata.com/help/kmanager/index.html?digital_inputs.htm I have all of the...
by AngryScottish
Mon Mar 05, 2018 3:07 pm
Forum: K-Pro / KManager
Topic: Sputtering at speed, can't figure it out.
Replies: 6
Views: 2691

Re: Sputtering at speed, can't figure it out.

After a frustrating few weeks, finally got the engine to run right.

All because of a partially failing MAP sensor that never threw a code or any indication of it being the issue.


for those who come across this: try swapping the map sensor.
by AngryScottish
Mon Feb 05, 2018 3:56 pm
Forum: K-Pro / KManager
Topic: Sputtering at speed, can't figure it out.
Replies: 6
Views: 2691

Re: Sputtering at speed, can't figure it out.

More followup,

I re-calibrated the TPS sensor. Sputtering goes away, but will come back after some time.

Ordered another TPS to see if that fixes it.

Fun.
by AngryScottish
Thu Feb 01, 2018 8:28 pm
Forum: K-Pro / KManager
Topic: Sputtering at speed, can't figure it out.
Replies: 6
Views: 2691

Re: Sputtering at speed, can't figure it out.

For those who run into this issue in the future... while I haven't completely solved it, I have isolated it somewhat. I have an Acuity TPS, no IAVC. So, I have the throttle stop threaded out slightly so the car will idle. My TPS readings were 4% at fully closed. 98% at fully open. I readjusted the T...
by AngryScottish
Tue Jan 30, 2018 12:59 pm
Forum: K-Pro / KManager
Topic: Sputtering at speed, can't figure it out.
Replies: 6
Views: 2691

Re: Sputtering at speed, can't figure it out.

If the ECU works ok in another vehicle then you have either a mechanical issue or a wiring issue. You will have to use process of elimination to determine where the issue resides. Is there a possibility of it being tuning related? Perhaps knock ? I'd imagine a wiring issue would have been evident r...
by AngryScottish
Mon Jan 29, 2018 10:38 am
Forum: K-Pro / KManager
Topic: Sputtering at speed, can't figure it out.
Replies: 6
Views: 2691

Sputtering at speed, can't figure it out.

- what vehicle you have Non-Honda chassis - serial number of your K-Pro 41478 - version of software being used (from Help, About) 4.3.4; ECU is a KproV4 - the calibration (as an attachment) below - a datalog of a problem (as an attachment) below - anything about the car which has been modified from ...
by AngryScottish
Wed Jan 17, 2018 9:54 am
Forum: K-Pro / KManager
Topic: ECU repair?
Replies: 5
Views: 2461

Re: ECU repair?

Thanks for the response. Since I'm stubborn and refuse to think the ECU is dead. I triple-checked my wiring -- found a loose pin for the MAP sensor. Got that fixed, engine fired right up. Downside, I bought $60 worth of sensors. Plus side, I have 3 replacement sensors in case they ever fail. Moral o...
by AngryScottish
Tue Jan 16, 2018 11:04 am
Forum: K-Pro / KManager
Topic: ECU repair?
Replies: 5
Views: 2461

Re: ECU repair?

41478