Search found 50 matches
- Wed Dec 19, 2007 10:12 am
- Forum: K-Pro / KManager
- Topic: Innovate LM1 or AEM and PRA ecu
- Replies: 12
- Views: 6407
If i understand correctly, extend the ground wire for the lm-1 to the intake manifold for better grounding? i think i'll try to ground the LM1 to the intake manifold tonight and see. or should i use the AEM because it has only 1 signal wire to be connected to the ECU? and put the voltage values int...
- Tue Dec 18, 2007 5:26 pm
- Forum: S300 Calibrations
- Topic: Need H22 map for RC750's
- Replies: 3
- Views: 3725
I was able to get it to run half way decent. It has a slight bog of idle but it will do til I get ready to send it over for a down pipe and tune. Its still stock at the moment just running rich but better then lean. Reguarding the wide band. I plan on getting one in the near future. Running a narro...
- Tue Dec 18, 2007 3:41 pm
- Forum: s300 / SManager
- Topic: rich on cold start up
- Replies: 13
- Views: 9231
well its supose to be a map that was tune for my setup, but its acually a map from hondata calibration forum. How do i know this? i downloaded a b18c map with a revhard set up and it pretty much mirrors my calibration. So now im trying to learn this tuning thing myself with forums help and a few bo...
- Tue Dec 18, 2007 3:26 pm
- Forum: s300 / SManager
- Topic: rich on cold start up
- Replies: 13
- Views: 9231
- Tue Dec 18, 2007 2:58 pm
- Forum: K-Pro / KManager
- Topic: Innovate LM1 or AEM and PRA ecu
- Replies: 12
- Views: 6407
If the LM1 manual states 1V=10:1 etc, then use those values. As far as wiring goes, the rule is to use a single ground point for everything in order to prevent ground loops. Unfortuently Honda has put the single ground point on the intake manifold, but that is what should be used. Additional ground...
- Tue Dec 18, 2007 11:55 am
- Forum: K-Pro Calibrations
- Topic: Why does the hondata k20a basemap run so much timing?
- Replies: 5
- Views: 4806
The vehicles were all tuned on 91 octane fuel here. Be aware that a restricted exhaust or hot air intake (short ram) will increase the chance of knock. Also remember that most states switch to winter fuel around the start of November which, despite the same octane rating, will knock more. What he s...
- Tue Dec 18, 2007 11:53 am
- Forum: K-Pro Calibrations
- Topic: DC5 JDM ITR map needed - Cat back and induction only
- Replies: 6
- Views: 4367
DO NOT USE THE RSX CAI MAP! If you're not comfortable making any changes and you're looking for an inexpensive way to have your car adjusted, email me.DC5mart wrote:Can I use the RSX CAI map? I read somewhere that you open the map in notepad and change the ECU value from 3 to 2?
Can anyone confirm :?
- Tue Dec 18, 2007 11:46 am
- Forum: K-Pro / KManager
- Topic: Innovate LM1 or AEM and PRA ecu
- Replies: 12
- Views: 6407
For datalogging purposes only you must go to Options, Settings, Wideband Input tab and choose the input you wish to use. Are the conversion tables for the lm-1 accurate or do they need to be adjusted? I've read the lm-1 manual and it does state that 1 input volt=10.0 af and 2 input volts=20.0 af. I...
- Tue Dec 18, 2007 10:26 am
- Forum: K-Pro / KManager
- Topic: Innovate LM1 or AEM and PRA ecu
- Replies: 12
- Views: 6407
- Tue Dec 18, 2007 12:58 am
- Forum: K-Pro / KManager
- Topic: 1000cc inj cold idle problems
- Replies: 6
- Views: 3428
- Mon Dec 17, 2007 7:54 pm
- Forum: K-Pro / KManager
- Topic: Temperature Compensation Not doing its job?
- Replies: 6
- Views: 3117
- Fri Dec 14, 2007 4:14 pm
- Forum: K-Pro / KManager
- Topic: Temperature Compensation Not doing its job?
- Replies: 6
- Views: 3117
Temperature Compensation Not doing its job?
I tuned a car and input different values for colder temperatures. Colder temperatures came, car started doing lean cuts. I had to do a seperate calibration due to several attempts of adjust temperature compensation tables. 1) Cold temperatures came in 1 week after tune was done 2) More fuel in the t...
- Sun Aug 05, 2007 2:35 pm
- Forum: K-Pro / KManager
- Topic: CEL's on, Can't datalog, 4000rpm limp mode----please help
- Replies: 29
- Views: 14067
- Mon Jul 23, 2007 11:27 pm
- Forum: K-Pro / KManager
- Topic: kpro and adjustable exhaust cam gear
- Replies: 4
- Views: 2868
- Mon Jul 23, 2007 11:25 pm
- Forum: K-Pro / KManager
- Topic: Kpro daatalogging problems
- Replies: 10
- Views: 3918