Search found 173 matches
- Sat Sep 23, 2006 8:43 am
- Forum: s300 / SManager
- Topic: How to get file off of S200 chip to open in SManager
- Replies: 8
- Views: 4497
- Tue Sep 19, 2006 5:41 pm
- Forum: s300 / SManager
- Topic: d16 will not boost past 5000rpm
- Replies: 14
- Views: 6904
- Tue Aug 08, 2006 1:04 pm
- Forum: s300 / SManager
- Topic: constantly changing voltage offset on wideband?
- Replies: 9
- Views: 4919
- Wed Aug 02, 2006 1:30 pm
- Forum: s300 / SManager
- Topic: PLX and capacitor
- Replies: 9
- Views: 6212
- Wed Jul 26, 2006 9:59 am
- Forum: s300 / SManager
- Topic: HELP HELP 3 bar question
- Replies: 4
- Views: 2638
- Wed Jul 12, 2006 8:02 am
- Forum: s100/s200
- Topic: At wide open throttle, hondalogger reads 88%.
- Replies: 4
- Views: 2511
Re: At wide open throttle, hondalogger reads 88%.
Your TPS sensor isn't set properly.ITEracer wrote:Should every properly working TPS read 100% in logger? The throttle plate is open all the way at WOT, but logger reads 88% maximum. In my old logs, the highest I would see it go is 92%
Small power loss lately, trying to figure out why.
- Mon Jul 10, 2006 9:47 am
- Forum: s300 / SManager
- Topic: How do I wire in my Wideband?
- Replies: 25
- Views: 12151
- Fri Jul 07, 2006 8:55 am
- Forum: s100/s200
- Topic: s200 to s300
- Replies: 9
- Views: 4584
You would have to have a pocket programmer or some kind of eeprom reader to read the file out of the chip. cool thanks another question:::how would you get it out of the chip if you just get a rom editor for the s200...wolud it be the same..???? You use the pcoket programmer to read the chip and sa...
- Tue Jul 04, 2006 5:57 pm
- Forum: s100/s200
- Topic: Bizarre S200B Question
- Replies: 3
- Views: 2548
- Mon Jul 03, 2006 8:17 am
- Forum: s300 / SManager
- Topic: Looking for info on FTS
- Replies: 13
- Views: 7013
Re: Looking for info on FTS
All you have to do is put one wire from ground to the clutch switch, then from the other side of the switch put another wire going to one of the input selection. For instance, I cut my P/S wire and put the sclutch switch wire in it's place. And yes the factory cruise control switch can work. Did yo...
- Mon Jun 05, 2006 11:48 am
- Forum: s300 / SManager
- Topic: PLX WB reading differ only when hooked into hondata
- Replies: 8
- Views: 4181
are u talking about the gauge reading on the PLX or the reading in Hondata itself. I noticed that I have to adjust my offset voltage pretty regularly to get correct readings. I have also been working with the PLX engineers to figure out their heating problems. On my car, if the unit is hot, it won'...
- Sat Jun 03, 2006 10:35 am
- Forum: s300 / SManager
- Topic: PLX WB reading differ only when hooked into hondata
- Replies: 8
- Views: 4181
- Thu May 25, 2006 6:36 am
- Forum: s100/s200
- Topic: 3bar install
- Replies: 1
- Views: 1225
- Thu May 04, 2006 4:39 pm
- Forum: s300 / SManager
- Topic: P28 ECU Problems? HELP!
- Replies: 19
- Views: 9558
That is NOT what I have. Do you even read what I'm posting? I just got done saying TWICE that I have it setup in the S300 correct. I will repeat once again... In the software under settings I have it set at O2 sensor and the following: O2 Voltage - A/F Ratio 0.00 - 10.000 5.00 - 20.000 When i opene...
- Wed May 03, 2006 6:16 pm
- Forum: s300 / SManager
- Topic: P28 ECU Problems? HELP!
- Replies: 19
- Views: 9558
You need to set the settings correct for the wideband. This is what you have now. http://sohchonda.com/ipw-web/gallery/albums/album33/Wideband_Settings.jpg also change it to Air/Fuel in the Lamda units. You will need the spec sheet from AEM and probably have to dial the voltage offset once you get i...