Injector Driver Box

Hondata model coverage & ECU application questions.
User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Injector Driver Box

Post by Hondata » Tue Jan 26, 2016 9:30 pm

That should work. Dead times have to be very accurate, and it helps if the injectors are spraying into the cylinder rather than hitting the manifold wall.
Hondata

cpl racing
Posts: 21
Joined: Thu Apr 29, 2004 12:13 am
Location: United Kingdom
Contact:

Re: Injector Driver Box

Post by cpl racing » Thu Jan 28, 2016 6:17 am

I assume that some kind of 'phasing' table will be added to the software so that the secondary injectors can be applied smoothly without any interruption in air fuel ratio ?
Hondata, Jackson Racing, Gruppe M, Dyno Dynamics

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Injector Driver Box

Post by Hondata » Thu Jan 28, 2016 6:42 pm

There is compensation for the wall wetting. As per the above post, dead times need to be accurate, then you can compensate for the fuel that hits the intake walls and doesn't make it into the cylinders. With intakes where the injector fires into the side of the manifold the effect is worse. The good news is that it seems to get easier at higher temperatures and injector durations.
Hondata

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Thu Jan 28, 2016 8:07 pm

has this wetting theory been tested visually? I see a lot of talk about it but its hard to comprehend this verses fuel spraying into an air stream of 50 pounds of boost and not atomizing into the flow very well at 1300 cfm.
www.MSSRACING.com
9.29 | 6.20 | 167

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Injector Driver Box

Post by Hondata » Fri Jan 29, 2016 8:51 pm

Yes, it was tested. It is a significant effect.
Hondata

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Fri Jan 29, 2016 9:06 pm

I don't really know how my 1000's aim I haven't looked at it. I have the s2 ultra on a B and the injectors are mounted in. iirc they are at a pretty good angle underneath.
www.MSSRACING.com
9.29 | 6.20 | 167

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Fri Feb 12, 2016 9:56 am

Can we get dimensions of the box? I've already built a sub harness for the secondary injectors to this box, but trying to pre plan as much as possible.
www.MSSRACING.com
9.29 | 6.20 | 167

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Injector Driver Box

Post by Hondata » Fri Feb 12, 2016 1:39 pm

Dimensions:
Width: 5" (127mm)
Depth: 4.25" (108mm)
Height: 1.5" (38mm)
Weight: 1.15 lbs (520g)
Mounting flange holes: 4 x 0.25" (6.35mm)
Mounting flange hole center: 4.5" (wide) x 2.9" (deep) (114.3mm x 73.7mm)
Hondata

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Fri Feb 12, 2016 2:40 pm

Sweet
www.MSSRACING.com
9.29 | 6.20 | 167

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Fri Mar 11, 2016 8:15 am

February came and went :/ :(
www.MSSRACING.com
9.29 | 6.20 | 167

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Injector Driver Box

Post by Hondata » Fri Mar 11, 2016 11:34 am

Yep. That's fairly typical over a 6 month project. Everything is ready apart from the packing boxes.
Hondata

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Fri Mar 11, 2016 1:31 pm

ok
www.MSSRACING.com
9.29 | 6.20 | 167

sass
Posts: 104
Joined: Mon Oct 06, 2008 5:07 am
Location: Evropa-Estonia-Tallinn

Re: Injector Driver Box

Post by sass » Thu Mar 17, 2016 1:12 am

I think correctly?

Image
Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Injector Driver Box

Post by Hondata » Mon Mar 21, 2016 9:17 am

Yes, that looks good.
Hondata

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: Injector Driver Box

Post by SPOOLIN » Wed Mar 23, 2016 3:51 pm

im guessing this was silently released in the last couple of days?
www.MSSRACING.com
9.29 | 6.20 | 167

Post Reply