Kpro v4 Analog input problem

K-Series Programmable ECU installation questions / support issues
Post Reply
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Kpro v4 Analog input problem

Post by Garrett_si »

Hi, I have a K24 engine, I use a AEM 0-150psi pressure sensor on input Analog 0

The display in psi was working a few week ago when I calibrate it, but now I see over 800psi in the display.

I verify the input voltage but changing the Sensor setting from Pressure to Raw voltage, and input voltage still fine.

I attached files and calibration + screen shot
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Re: Kpro v4 Analog input problem

Post by Garrett_si »

Here is the files and screen shots
Attachments
run21.kal
(166.99 KiB) Downloaded 133 times
50875331_2147598125283874_7269611492876484608_n.png
50875331_2147598125283874_7269611492876484608_n.png (122.26 KiB) Viewed 5745 times
50936391_361201524677416_3915947650582577152_n.png
50936391_361201524677416_3915947650582577152_n.png (123.7 KiB) Viewed 5745 times
50334671_792847544423922_6138896279154982912_n.png
50334671_792847544423922_6138896279154982912_n.png (127.86 KiB) Viewed 5745 times
User avatar
Spunkster
Site Admin
Posts: 22740
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: Kpro v4 Analog input problem

Post by Spunkster »

Post datalogs that show the issue. Screenshots are not enough.
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Re: Kpro v4 Analog input problem

Post by Garrett_si »

Here is the datalog file
Attachments
run21.kal
(167.34 KiB) Downloaded 141 times
User avatar
Spunkster
Site Admin
Posts: 22740
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: Kpro v4 Analog input problem

Post by Spunkster »

That is your calibration and not a datalog.
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Re: Kpro v4 Analog input problem

Post by Garrett_si »

sorry

here is the log
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Re: Kpro v4 Analog input problem

Post by Garrett_si »

here is the log
Attachments
run21.kdl
(6.09 MiB) Downloaded 149 times
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Re: Kpro v4 Analog input problem

Post by Garrett_si »

Did you see something wrong?
User avatar
Spunkster
Site Admin
Posts: 22740
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: Kpro v4 Analog input problem

Post by Spunkster »

What oil pressure sensor are you using?

Can you post a Datalog that shows the raw voltage?
Garrett_si
Posts: 248
Joined: Wed May 17, 2006 9:49 am

Re: Kpro v4 Analog input problem

Post by Garrett_si »

Sensor is honeywell 0-150psi
Raw voltage could be seen is Hondata software allow it like other standalone I think it's a necessity
Post Reply