Datalogging JDM ITR - Reading wrong speed / gear?
Datalogging JDM ITR - Reading wrong speed / gear?
Hi All,
Ive a JDM ITR K20a DC5. Ive put on a PRB KPRO and uploaded a base kal with breathing mods.
Did a 3rd gear pull and it was reading gear 2 instead of 3 and the speed of 2nd gear. So readying the wrong gears rather than the speed i guess.
Any help on this?
Thanks
Jay
Ive a JDM ITR K20a DC5. Ive put on a PRB KPRO and uploaded a base kal with breathing mods.
Did a 3rd gear pull and it was reading gear 2 instead of 3 and the speed of 2nd gear. So readying the wrong gears rather than the speed i guess.
Any help on this?
Thanks
Jay
Just checked it and it had the following ratios in my current base map given to me.
[Gear Ratios]
; Gear ,Ratio
0=1,3.266
1=2,2.13
2=3,1.517
3=4,1.147
4=5,0.921
5=6,0.738
6=7,4.764
I then updated it with what was in the KPRO Gear Comp section to JDM Integra R and its this. But still showing the wrong gears.
[Gear Ratios]
; Gear ,Ratio
0=1,3.266
1=2,2.13
2=3,1.517
3=4,1.212
4=5,0.972
5=6,0.78
6=7,4.764
Also got P0134 Air Fuel Ratio Sensor Not Active now :(
Any ideas?
[Gear Ratios]
; Gear ,Ratio
0=1,3.266
1=2,2.13
2=3,1.517
3=4,1.147
4=5,0.921
5=6,0.738
6=7,4.764
I then updated it with what was in the KPRO Gear Comp section to JDM Integra R and its this. But still showing the wrong gears.
[Gear Ratios]
; Gear ,Ratio
0=1,3.266
1=2,2.13
2=3,1.517
3=4,1.212
4=5,0.972
5=6,0.78
6=7,4.764
Also got P0134 Air Fuel Ratio Sensor Not Active now :(
Any ideas?
sorry to hijack but just wan to share
previous i don't have any speed sensor and just put provide constant speed
after some time i put back the speed sensor the motor get miss firing on 2nd and 3rd gear only in certain rpm its was gone after the engine exceed 3.5k rpm and its only happen in 1,2,3rd gear 4th gear above will fine
here some of my datalog file any 1 here can help me out?
previous i don't have any speed sensor and just put provide constant speed
after some time i put back the speed sensor the motor get miss firing on 2nd and 3rd gear only in certain rpm its was gone after the engine exceed 3.5k rpm and its only happen in 1,2,3rd gear 4th gear above will fine
here some of my datalog file any 1 here can help me out?
- Attachments
-
- 2nd gear miss.kdl
- (44.78 KiB) Downloaded 145 times
ok its just happen on 1st 2-3 sec on the datalog you could saw the ignition turn to -5 degree and the engine was miss fire therecranny wrote:your car needs tuning dude. post up your calibration. runs pig rich fom what i see.
when i unplug the speed sensor and provide constant speed in kpro every things will fine A/F will going back to 12.8-13.3 its only happen VSS was running/attach
Rather than start a new thread...I have the same/similar problem.
I have a 2001 JDM Integra Type R DC5 with a K20a.
In Japan the speedo reads KPH. When imported to the UK the speedo was converted to MPH.
When I'm traveling at 70MPH KManager reads 43MPH.
I am aware 43MPH = 70KPH
Have I simpley missed a setting within the sofware?
Cheers,
I have a 2001 JDM Integra Type R DC5 with a K20a.
In Japan the speedo reads KPH. When imported to the UK the speedo was converted to MPH.
When I'm traveling at 70MPH KManager reads 43MPH.
I am aware 43MPH = 70KPH
Have I simpley missed a setting within the sofware?
Cheers,
Ian
Morris Mini (B18C-R)
Honda Civic Type R (FD2)
Honda Civic Type R (FK2)
Morris Mini (B18C-R)
Honda Civic Type R (FD2)
Honda Civic Type R (FK2)