SManager software requests

s300 and SManager software questions & answers
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager software requests

Post by Johnny_9 »

Tip-in trim by rpm, +% and decay rate. Really need this.
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager software requests

Post by Johnny_9 »

OBD1 to OBD2 protocol converter
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager software requests

Post by Johnny_9 »

Need a much better compare calibration function.
Amon
Posts: 2
Joined: Wed Mar 21, 2012 11:18 am

Re: SManager software requests

Post by Amon »

I would like to see a detailed history function so I can see what I did previously.
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

No help on tip-in fuel v ECT

Post by Johnny_9 »

?
portenio78
Posts: 38
Joined: Mon Oct 24, 2011 6:43 am

Re: SManager software requests

Post by portenio78 »

Stock d16y8 calibration.
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager software requests

Post by Johnny_9 »

serial output to log all ECU parameters.
FreshDA9
Posts: 252
Joined: Sun Jul 27, 2008 8:40 pm

Re: SManager software requests

Post by FreshDA9 »

Hows about a pressure vs duty cycle table based on map sensor selection. under boost control parameters. having more cells will allow better adjusting for desired psi.

live logging in the battery offset tables will help will help a lot, also logging of anything in the parameters tab!

Another option for widband logging. Being able to log only a selected gear. this will clean up a lot of Overrun when on dyno or street. Just be able to make a check box for N-5 gear also stop logging on fuel cut.

Hows about serial logging support for widebands. no more playing with voltage offsets just put your usb in and select your port and go.

Custom target AFR for whole map, not just 3 columns.
above are some old request.

Would also be nice to remove the 2D/3D graph simple button click.
EFI-101 & Advanced Certified*
portenio78
Posts: 38
Joined: Mon Oct 24, 2011 6:43 am

Re: SManager software requests

Post by portenio78 »

Overlay 2 log graphs over eachother?
joeb
Posts: 25
Joined: Wed Sep 06, 2006 8:39 am
Location: tiverton ri

Re: SManager software requests

Post by joeb »

I know this has come up before . It would be fantastic if we could use the knock sensor and log knock properly . I see this feature with the dsm guys and it is invaluable .
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: SManager software requests

Post by Hondata »

The knock logic is handled completely by the knock daughter board. The only interface is a suggested knock retard, which is what's datalogged.
Hondata
kerndog
Posts: 30
Joined: Mon Dec 24, 2007 11:46 am

Re: SManager software requests

Post by kerndog »

I would like to have 2 seperate boost cuts---one for primary and secondary tables, or linked to the low and high boost tables? I'm going to push it a little and ask for 2 quick spool tables as well, and have it possible to set them to the same switch that changes to secondary tables similar as the low and high boost.
H22 GT3076R E85, EK Hatch, Dyno Shootout Car...
603 WHP, 565 WHP, 631 WHP, 596 WHP, 600 WHP, 610 WHP, 631 WHP, 560 WHP, 578 WHP
different dynos, different days, different altitudes,same set-up, bottom line...~600ish WHP come get some!!!
SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: SManager software requests

Post by SPOOLIN »

check box to make launch limiter/anti lag override the activated burn out rev limiter.

once it gets past its set mph it will then use the burn out rev limiter.

this way your not trying to start turning over slicks with 6 psi in them from a dead rev limiter with no power behind it.
www.MSSRACING.com
9.29 | 6.20 | 167
ITR1102
Posts: 46
Joined: Tue Jan 26, 2010 8:34 am

Re: SManager software requests

Post by ITR1102 »

I like the red cell trace line that is used in KManager. That really helps me see where I am at in each cell while live tuning (street tuning). Is this possible to incorporate into SManager?
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Injector dead time vs Fuel Pressure

Post by Johnny_9 »

Injector dead time vs Fuel Pressure/Volts.
Post Reply