SManager software requests

s300 and SManager software questions & answers
Luke
Posts: 249
Joined: Thu Mar 26, 2009 10:24 am
Location: Dorsten/Germany

Re: SManager software requests

Post by Luke »

well, but the datalogging is some serial (TTL) stuff, on the S300 is a FTDI chip, so a serial to USB converter (or is that something else?) - maybe my electrotechnical knowledge isn't good enough, but in my opinion that shouldn't be such a big deal.

well, said this, without knowing the exact procedure of reading the datalogging port. anyways. maybe there will be a solution.

for the rev limit recovery: maybe it could be made even closer, for anti-lag. or just to erase that annoying sound :D

best regards Lukas
turbo-2nr
Posts: 42
Joined: Fri Sep 01, 2006 2:08 am

Re: SManager software requests

Post by turbo-2nr »

it would also be nice to have gear based revlimits and shift lights along with boost by speed
Luke
Posts: 249
Joined: Thu Mar 26, 2009 10:24 am
Location: Dorsten/Germany

Re: SManager software requests

Post by Luke »

according to the closer target lambda setting, it would be nice to have different targets for secondary maps or, what would be even better, fully different settings for secondary maps, to change everything individually, when neccessary

best regards Lukas
Alli
Posts: 3
Joined: Thu Dec 10, 2009 4:56 am

Re: SManager software requests

Post by Alli »

I would really like a "learning" ability with the duty cycle vs pressure in the boost control section
FreshDA9
Posts: 252
Joined: Sun Jul 27, 2008 8:40 pm

Re: SManager software requests

Post by FreshDA9 »

Injector offset drop down menu. close offsets for many injectors that are popular today such as ID, RC, Percision, etc. something close to start with. I used deatchwerks starting offsets they sent me and didnt work so well. something that you guys can test and make it easier for us so we can fine tune.

Also i know someone said but better resolution for a/f target please.
EFI-101 & Advanced Certified*
Lazysk8r2
Posts: 72
Joined: Fri Apr 14, 2006 2:26 pm

Re: SManager software requests

Post by Lazysk8r2 »

i dunno if it would be possible but put in a turbo timer, that would be nice.
Street Tuner/Dyno Tuner
turbo-2nr
Posts: 42
Joined: Fri Sep 01, 2006 2:08 am

Re: SManager software requests

Post by turbo-2nr »

IMO turbo timers are a joke unless u have a super bad ass oil cooler with a fan on it and even then the car would have to run for 10min plus for any effect
AREA876
Posts: 420
Joined: Tue Jun 15, 2010 6:14 am
Location: Jamaica

Re: SManager software requests

Post by AREA876 »

I would love to see Boost Control (PWM) enable through output A17 (IAB) for a JDM ECU
MarkC
Posts: 20
Joined: Fri Apr 09, 2004 12:29 pm
Contact:

Re: SManager software requests

Post by MarkC »

Alli wrote:I would really like a "learning" ability with the duty cycle vs pressure in the boost control section
I second this! I think it would be fun to program too.
spoolind16
Posts: 21
Joined: Thu Jul 05, 2007 10:07 am

Re: SManager software requests

Post by spoolind16 »

It would be nice to have the ablity to turn the fuel pump relay on and off with key-on engine-off. More than once I wanted to drain my fuel and had to rig a battery to the pumps.

Also the ablity to reivew if lean protection kicked in in the sensors window (similar to the way you have BstC displayed)
Jaker
Posts: 139
Joined: Thu Dec 05, 2002 12:37 pm
Location: Vancouver, BC
Contact:

Re: SManager software requests

Post by Jaker »

AREA876 wrote:I would love to see Boost Control (PWM) enable through output A17 (IAB) for a JDM ECU
I think A17 is just an on or off circuit. You need a variable output for PWM.
Luke
Posts: 249
Joined: Thu Mar 26, 2009 10:24 am
Location: Dorsten/Germany

Re: SManager software requests

Post by Luke »

Jaker wrote:
AREA876 wrote:I would love to see Boost Control (PWM) enable through output A17 (IAB) for a JDM ECU
I think A17 is just an on or off circuit. You need a variable output for PWM.
PWM is an on and off switching. just in a certain pulse width.
jiggacivic
Posts: 35
Joined: Wed Oct 08, 2008 12:55 pm

Re: SManager software requests

Post by jiggacivic »

could Gear be one of the options in conditions menu the Nitrous/Aux so the nitrous would not be armed if it is not in that particular gear.
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Idle Closed Loop AFR

Post by Johnny_9 »

Like K-Pro

Image

Uploaded with ImageShack.us
Last edited by Johnny_9 on Tue Jul 19, 2011 5:46 am, edited 1 time in total.
Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Datalog IACV Duty cycle

Post by Johnny_9 »

Make the IACV duty cycle visible in the sensor and datalogs.

Image

Uploaded with ImageShack.us
Post Reply