SManager software requests
SManager software requests
Since requests for changes tend to get scatter all over the forum, I have created an official software request thread.
I don't promise to respond to every request, but I do read all new posts.
I don't promise to respond to every request, but I do read all new posts.
Hondata
Bluetooth for S300?!
Hi Folks,
The S300 is now a couple of years on the market, wouldn't it be great, to get a hardware update?
Some more memory for datalogging and bluetooth?
since the communication is some serial protocol, this should work just fine via SPP in bluetooth.
this would be great! another option would be then to write some android/iphone app to datalog the data with the smartphone.
wouldn't that be possible?
best regards Lukas
The S300 is now a couple of years on the market, wouldn't it be great, to get a hardware update?
Some more memory for datalogging and bluetooth?
since the communication is some serial protocol, this should work just fine via SPP in bluetooth.
this would be great! another option would be then to write some android/iphone app to datalog the data with the smartphone.
wouldn't that be possible?
best regards Lukas
closed loop target lambda
Please implement access to closed loop target lambda tables like K-Pro !
Re: SManager V1.5.1 beta
a selectable target lambda option would be great, one for the primary map, one for the secondary map.
well, and more breakpoints than 3 in the options.
*sorry, wrong thread...*
best regards Lukas
well, and more breakpoints than 3 in the options.
*sorry, wrong thread...*
best regards Lukas
Re: Bluetooth for S300?!
Thats would be awsome.
Re: SManager software requests
This plus Serial wideband logging.Luke wrote:a selectable target lambda option would be great, one for the primary map, one for the secondary map.
well, and more breakpoints than 3 in the options.
Another option for widband logging. Being able to log only a selected gear. this will clean up alot of Overrun when on dyno or street. Just be able to make a check box for N-5 gear also have a lean stop logger so if your wide open put 16 as lean over by the time you see 16 in wot you should have the foot off the gas pedal anyways, or you could set it up as dont log fuel cut.
adding and removing speedlimiters would be good, too
EFI-101 & Advanced Certified*
Re: SManager software requests
for us drag guys it would be nice to have boost by ground speed ,use a rear abs sensor for the ground speed
this one thing i notice ppl switch over to aem and motec for and this option would help us small guys out lot
this one thing i notice ppl switch over to aem and motec for and this option would help us small guys out lot
Re: SManager software requests
I would love to see Boost Control (PWM) enable through output A17 (IAB) for a JDM ECU
-
- Posts: 192
- Joined: Wed Aug 22, 2007 12:41 am
Re: SManager software requests
I would like to be able to lock and password protected the fuel and ignition map atleast.
Re: SManager software requests
this would be great.V-Spec race development wrote:I would like to be able to lock and password protected the fuel and ignition map atleast.
a "customer" version of smanager, where he can change LC, Full Throttle Shift and shift light (without the option of manipulation anything else) would be some good option, as well.
best regards Lukas
Re: SManager software requests
I do not agree with ever locking the maps. A customer pays us to tune the car, he then owns all rights to his map for whatever he wants to do. If the maps were locked, it would surely be a pain for a customer if the tuner went MIA.
With that said, I'd like to see a way to datalog more 0-5v and digital inputs, and perhaps be able to do something with that data. Perhaps an external datalogger for use with S300/Kpro/etc..
With that said, I'd like to see a way to datalog more 0-5v and digital inputs, and perhaps be able to do something with that data. Perhaps an external datalogger for use with S300/Kpro/etc..
Locash Racing, LLC
Hondata Sales and Tuning
Dynapack 4000 2wd Dyno
In-Shop CNC Machining and Product Manufacturing
Hondata Sales and Tuning
Dynapack 4000 2wd Dyno
In-Shop CNC Machining and Product Manufacturing
Re: SManager software requests
surely, the customer has the rights to get the map, of course.
but don't forget, the a lot of people don't have the knowledge about the behavior of engines.
this is seriously meant to protect the engine.
best regards Lukas
but don't forget, the a lot of people don't have the knowledge about the behavior of engines.
this is seriously meant to protect the engine.
best regards Lukas
Re: SManager software requests
Regardless, its the customers engine as well, if he wants to blow it up, it is his right to do so. :)
Oh, forgot to add the request to move all analog input tables to the calibration file, as it is a pain to re-enter the values every time I tune a car with something different in those tables..
Oh, forgot to add the request to move all analog input tables to the calibration file, as it is a pain to re-enter the values every time I tune a car with something different in those tables..
Locash Racing, LLC
Hondata Sales and Tuning
Dynapack 4000 2wd Dyno
In-Shop CNC Machining and Product Manufacturing
Hondata Sales and Tuning
Dynapack 4000 2wd Dyno
In-Shop CNC Machining and Product Manufacturing
Re: SManager software requests
Joe - if the analog tables are in the laptop, why do they need to be re-entered? Are you using the customer's laptop?
The issue with moving the tables to the calibration is when datalogging - you would need to have the calibration loaded.
Would some drop downs with common values help for the short term?
The issue with moving the tables to the calibration is when datalogging - you would need to have the calibration loaded.
Would some drop downs with common values help for the short term?
Hondata
Re: SManager software requests
Thats the problem, I use my laptop to tune, yet not every car is using the same sensor on its analog input.. I dont mind having the calibration loaded to view the datalog, it makes sense to do that anyway..
Locash Racing, LLC
Hondata Sales and Tuning
Dynapack 4000 2wd Dyno
In-Shop CNC Machining and Product Manufacturing
Hondata Sales and Tuning
Dynapack 4000 2wd Dyno
In-Shop CNC Machining and Product Manufacturing