RC 660 Injectors
RC 660 Injectors
So I'm turbo charging my H23 and in preparation I have installed a Walbro pump and RC 660 injectors... After the install I started it up to check it out and it ran really rough. I increased the fuel tables and got it to idle very nice and it revs alright... When I took it for a test drive on the up hills it didn't have too much power. I think its running very lean. Should I be concerned with making it run well before I install the turbo or should I just wait till after the turbo to tune it? I datalogged my test drive.
- Attachments
-
- RC660inj.s3d
- (663.9 KiB) Downloaded 475 times
Re: RC 660 Injectors
In my opinion make it run well first how many pounds are u boosting?theodd001 wrote:So I'm turbo charging my H23 and in preparation I have installed a Walbro pump and RC 660 injectors... After the install I started it up to check it out and it ran really rough. I increased the fuel tables and got it to idle very nice and it revs alright... When I took it for a test drive on the up hills it didn't have too much power. I think its running very lean. Should I be concerned with making it run well before I install the turbo or should I just wait till after the turbo to tune it? I datalogged my test drive.
Since your boosting more than 6psi if you want your car to run good try to aim your airfuel at 11.0-11.2 but is best if you could get it around 11.2. If you decide to boost less than 8psi and go with 6psi try to get your airfuel around 12.0-12.2 but is best if you get 12.2 on your airfuel reading.theodd001 wrote:Just a max of 10psi but daily I will be running 8lbs.
I have an A/F meter on my stock O2 sensor, that I am using but when I get the turbo and downpipe on I will install the AEM uego controller that I have, it comes with digital gauge that can output in AFR or Lambda and a Bosch wideband sensor. It ranges from 10 - 20 AFR and has the 0-5 volt output that can wire into the s300. Im excited about it. Oh and I have a matching AEM digital Boost gauge, it goes from 30" of vacuum to 30lbs of boost.
http://www.aemelectronics.com/wideband- ... -gauge-25/
http://www.aemelectronics.com/boost-gauge-35-psi-767
8)
http://www.aemelectronics.com/wideband- ... -gauge-25/
http://www.aemelectronics.com/boost-gauge-35-psi-767
8)
-
- Posts: 38
- Joined: Sat Oct 28, 2006 7:27 pm
holy crap, extremely lean!!!! do not run the car like that...cruising u should be targeting 14.7. u go from 0-100%tps and no change in air fuel ratio this is bad. make sure u get the car running right before u put boost into it. whatever map u have doesnt look good at all. i would load one of the stickies on here first and start from there. there are good base maps out there. full boost aim for 12-12.5 air fuel.
also make sure u get that wideband installed and wired into the ecu asap. theres no point in tuning without one.
also make sure u get that wideband installed and wired into the ecu asap. theres no point in tuning without one.
-
- Posts: 38
- Joined: Sat Oct 28, 2006 7:27 pm
yeah like I was telling him, you have to have a wideband if you want to attempt to tuned your car.snwbrdrx19 wrote:not necessarily but u wont be able to tell anything until that wide band gets wired in. until then i wouldnt really drive it without knowing where its at. no point in ruining a motor for nothing.